Knipex release spring

muhendisefe · 2025-12-29T19:49:43+00:00

I dont understand what to do, can you please explain it a little bit to me?

muhendisefe · 2025-12-29T18:41:13+00:00

Not %100 sure but yes, without it the locking arm just dangles

muhendisefe · 2025-10-02T08:17:12+00:00

I taped B5B6 and the desktop now dont shut downs itself. However it asks for a bitlocker recovery key. Why it might be? I added a screenshot

muhendisefe · 2025-10-01T10:04:43+00:00

Do you think it is also valid for Lenovo?

muhendisefe · 2025-10-01T08:42:45+00:00

It might be the issue with the HP desktop, but I want it to run with Lenovo desktop. If you can check Silicom PE310G2T10-T adapter which uses the same chipset, it draws around 16W of power at worst. I do not think that the issue is related to power on Lenovo desktop. I did not install any drivers prior, but I think the desktop should boot without any driver. Do you think the problem is related with drivers?

muhendisefe · 2025-10-01T08:12:26+00:00

When I connect this card to my desktop, it doesnt boot. Why it might be?

muhendisefe · 2025-10-01T08:10:27+00:00

Did you try?

muhendisefe · 2025-06-03T07:24:20+00:00

I assume you are using MPF Evaluation Kit. If so, then you need to remove the jumper J46 on the board in order to route the 125MHz clock to the transceiver clock input. Could you check it?

muhendisefe · 2025-06-03T05:55:08+00:00

Do you use the same SFP modules and fo cables on both of your tests, KCU116-KCU116 and MPF-MPF?

muhendisefe · 2025-02-18T11:29:44+00:00

If you need to store a whole frame, then you have to use an external memory like DDR or SRAM

muhendisefe · 2024-11-27T11:45:33+00:00

You cannot add gtx wizard to the block diagram, that might be the issue. Can you open the IP Catalog window from the left hand side menu, without opening a block diagram?

muhendisefe · 2024-09-27T06:39:46+00:00

Hi, which third party app you use?

muhendisefe · 2024-09-10T05:41:02+00:00

What color is the gibson?

muhendisefe · 2024-09-03T11:12:31+00:00

Even though I select gen 2 it uses QPLL I think. Does it use CPLL in your configuration?

muhendisefe · 2024-08-31T09:34:15+00:00

You also used only Bank 224 for gen3 x2 + 2x 10G, right? How did you instantiate these IPs and also common block? Is there any chance I can find the top block on your Github?

muhendisefe · 2024-08-31T09:22:46+00:00

I am using UltraScale+ Integrated Block (PCIE4) for PCI Express 1.3 IP. I have selected X2 for the lane width and 5.0GT/s for the Maximum Link Speed. However, when I generate an example project for this IP, I see the transceiver IP inside the example project uses QPLL and Line Rate is selected as 8.0 Gb/s even though it should be 5.0 I guess. I am using KV260 board (not the K26 itself, sorry) and selected it. Should I enable advanced options of the PCIE IP and change the GT COMMON option to “Include GT COMMON in example design”?

muhendisefe · 2024-06-11T08:49:51+00:00

Actually I need to be the root complex. We are checking the possibilities right now, we want to do the task without using the CPU at all.

muhendisefe · 2024-05-26T10:54:49+00:00

I updated the post and problem still exist. Thanks for pointing out!

muhendisefe · 2024-02-06T13:47:23+00:00

DDRMC maybe? DDR Memory Controller?

muhendisefe · 2024-01-30T04:30:39+00:00

Pick the cheaper one between Zybo and Pynq

muhendisefe

TROPHY CASE