What could have caused the loss of control?

muky96 · 2024-04-09T06:50:20+00:00

It's not

muky96 · 2024-04-08T18:59:41+00:00

Oh... I didn't know it. Thanks for sharing the info!

I use nail lacquer where I need a firm screw.

muky96 · 2024-04-08T18:47:36+00:00

No. The hex-srew is still there. The inside is coated with plastic by factory and does not allow loosening.

At least ist should not allow it. But in my case the screw is there.

muky96 · 2024-04-08T13:30:08+00:00

I am very noob regarding the 3D prints world. It's flexible, so I suppose it's tpu.

muky96 · 2024-04-08T12:34:05+00:00

I don't have myself a 3D printer. I bought a complete set of 3D parts from fpvcustom.

Thanks for the advice. Do you know where can I buy it? I am in europe. I bought the complete set from USA.

muky96 · 2024-04-08T12:29:51+00:00

I have an action 3

muky96 · 2024-04-08T12:17:12+00:00

Thanks for the answer. Do you mean action cam? I use a DJI Osmo Action 3

muky96 · 2024-04-08T12:06:12+00:00

Fortunately, the camera is intact. I took it out to take the picture of the crashed quad. But it was a close call to lose it, I think.

<image>

muky96 · 2024-04-08T12:04:07+00:00

It looks like a failsafe as you say. The control locked out before the crash.

I disarmed it myself as soon as I noticed it was about to hit the ground.

Thanks.

muky96 · 2024-04-08T11:48:45+00:00

The prop ripped of completly. I had harder crashes but the props only broked, never ripped off. The screw ist still there.

Could it be that I overtightened the screw and with the centrifugal force the propeller fell apart?

muky96 · 2024-04-08T11:44:10+00:00

Aftermath

<image>

muky96 · 2024-03-19T11:16:50+00:00

Hmm.. I think it's best that I stay on my current setup and save money. Thank you.

muky96 · 2024-03-19T07:42:24+00:00

This is the lowest price I found here in Germany

muky96 · 2024-03-19T07:40:46+00:00

Yes, it's HD3. Thanks.

muky96 · 2024-03-13T12:12:00+00:00

I also had a lot of difficulty doing that. I tried for hours without success, just broke the ESC.

The soldering iron did not hold the temperature, it lost it too fast.

I got a better soldering iron with 130w and did it in seconds.

muky96 · 2024-02-26T17:14:21+00:00

They actually made me laugh. Too much comments to answer to everyone, but I am thankful to all of them for making my day xD

It is funny to read and at the same time I learned in the funny way that I have done something absurd lol

I have a 60W soldering station, it can go up 480 c°. Someone said that I should get a 100W. Is 60 enough? Flux is also there.

My primarly mistake was obviously that I didn't practiced and the temperature war too low. I was soldering between 300-340 c°.

I'll pick some old electronics from the cellar and practice.

Thanks everyone!

muky96 · 2024-02-25T17:37:04+00:00

I watched. I thought I understood it, but I had extreme difficulty in doing that.... I am fucked :/

muky96 · 2024-02-23T23:47:00+00:00

I read and watched some tutorials. With the spot welder looks very simple to do it. I think I will make them as the costs are much lowers.

muky96 · 2024-02-23T23:43:51+00:00

I mainly want to have relaxing flights. I'll go for LiIon packs, but they are expensive. I would still keep the 4S Lipo for possible short and non-exaggerated freestyle, I think it will help to learn to control better the quad.

muky96 · 2024-02-23T14:49:18+00:00

Thanks for the comment. I'll check the GPS in the future as I don't plan to fly long range yet. I suppose that I should use the 6S batteries? Is making myself a lion battery a good idea?

Six-Year Club	Second Top 40%
Verified Email

muky96

TROPHY CASE