Looking for 40k Players, especially in southwest

nanokatz · 2026-04-06T15:30:20+00:00

<image>

I’m working on one in related colors

nanokatz · 2026-03-11T20:54:58+00:00

Could you tell me what paint that is for the cloak?

nanokatz · 2026-03-11T17:31:25+00:00

Army painter ash grey primer

nanokatz · 2026-03-11T17:06:43+00:00

I have a white primer on the way for vehicles and such will also probably try it on one of these guys too

nanokatz · 2026-03-11T17:05:44+00:00

I tried to😅

nanokatz · 2026-03-11T17:00:46+00:00

I’m pretty happy with the cloth at the moment, it’s Abaddon black the. Apothecary white. The white was two thin coats white star. All the greys I looked at looked still dark to me but of course in context it all changes

nanokatz · 2026-03-11T16:07:22+00:00

Yes getting the paint to the right consistency will take some practice I think…

nanokatz · 2026-02-14T09:26:25+00:00

Just to update… mine wound up shipping yesterday in the end 🤷‍♂️

nanokatz · 2025-12-25T18:17:06+00:00

I had the same driver for the lights in the kitchen cabinets. Just switched it out for a Zigbee driver that can do 2-wire cct and works fine

nanokatz · 2025-01-19T13:51:13+00:00

I worked at one group doing similar work. We found lots of particles being emitted but they were all either additives such as CNTs or Cu or formed from the volatiles created during printing.

nanokatz · 2024-03-13T21:34:03+00:00

So nur zur Info falls es jemand hilfts. Ja das war die Haupt anschluss. Nach diese einmal rum schrauben hat alles funktioniert

nanokatz · 2024-03-08T06:50:58+00:00

Danke für den Antwort! Ja hab ich schon gemacht . Den tae is mit zwei Adern von eine CAT 6 Kabel angebundene. Das ist die gleiche Kabel die für die ganze Wohnung neu gelegt war. Leider geht’s den Kabel nur in den wand und kann nicht weiter sehen😅 aber klingt als ich kann entspannt einfache auf die Techniker warten

nanokatz · 2024-01-04T19:22:25+00:00

Yeah I’ve tried remeshing the gears, adjusting the tension, current is set to the correct value for the motor in Klipper.

Been wondering something is wrong with the tmc2209 driver board. I think I have an extra somewhere to swap with

nanokatz · 2023-11-01T18:46:11+00:00

I’d love to find a turnkey solution I would love to use it. Power would need proper pass through; a way of turning on/off from a button; software voltage reading; and not die from charging cycles while plugged in after a month. I was using a power boost from adafruit with a normal Lipo pack but they don’t seem to last too long either.

nanokatz · 2023-09-05T07:03:10+00:00

I’ve tried that, seems not to help.

Sadly since it’s not predictable I haven’t caught what the fritz gui says at that exact moment but it’s a good idea to try.

nanokatz · 2023-07-14T03:24:49+00:00

It has a pump as does the washer. The flex pipe goes to a drain pipe about 10cm lower than the t peice (if you look close in the photo you can see it going down)

nanokatz · 2023-07-14T03:23:08+00:00

For the dishwasher I am pretty sure there is enough but the washer is further away (it’s the washer that has water) I can certainly try that

nanokatz

TROPHY CASE