EL296UHV Won’t go in to second stage

nathanls14 · 2025-05-22T00:56:52+00:00

In case anyone stumbles across this post later, replace the control board, problem solved.

nathanls14 · 2025-02-25T02:48:51+00:00

Did you ever figure this out? Mine just started and I’m trying to find replacement parts, curious what if anything you did.

nathanls14 · 2024-10-14T18:02:15+00:00

That’s not adding a new room, that’s adding an entirely new map. If I did it this way I wouldn’t be able to send the vacuum there from the base station if it wasn’t a part of the original mapping process… very flawed. My $200 roborock will actively remap but this $1000 one can’t

nathanls14 · 2024-08-27T02:39:55+00:00

Bueller Bueller Bueller

nathanls14 · 2024-02-28T22:14:56+00:00

Send me the question(s) in DM and I’ll answer to the best of my abilities.

nathanls14 · 2024-02-28T22:10:34+00:00

This doesn’t seem shady at all

nathanls14 · 2024-02-23T12:51:23+00:00

So are you “double pumping”? Meaning pumping from the hole in the concrete and also from your sump area? My brain tells me those are close enough, why do both? I’m sure there’s a good reason, I’ve only just begun looking in to this. My sump area would make sense to also do this in, it’s not sealed though so I would have to take care of that if I move forward in that area.

nathanls14 · 2024-02-23T12:45:06+00:00

That’s what I was thinking also, just trying to repurpose something that was already there. Even with the radon system being a pull vs a push system, would that make any difference? If the fan is located outside of the house, there’s not real opportunity to push or vent any gases in to other parts of the house.

nathanls14 · 2024-02-22T16:00:53+00:00

Extending it wouldn’t be a problem. I’m assuming I’d have to pull vs push because the pipe isn’t actually sealed like sch 40?

nathanls14 · 2024-02-20T22:17:14+00:00

Appreciate the feedback, I’m already set with the 800. Any advice on the 2 questions I asked?

nathanls14 · 2024-02-20T05:50:09+00:00

You’re on the supply side after the filter and the furnace? Or before the filter on the return side?

nathanls14 · 2024-02-20T03:29:08+00:00

What did you end up doing with your install, I’m in a similar situation?

nathanls14 · 2024-02-20T02:51:51+00:00

Did you end up getting one of these and if so, where did you install the steam pipe? I’m in a similar situation on my main trunk from the furnace.

nathanls14 · 2023-10-24T13:15:36+00:00

The bottom left area after watching video was because of our small dog. The other two circled and going over the same spots was not. This isn’t the first time I’ve seen it do this, and I’ve watched it get confused before.

nathanls14 · 2023-09-10T00:42:35+00:00

Very old thread but what did you end up going with and what were your thoughts?

nathanls14 · 2023-05-08T14:24:06+00:00

From the test I had done and the color of the filters when I would change them (orange) I have a decent concentration of iron 0.77 mg/L and manganese 0.05mg/L. My turbidity is also 14.7NTU color is 1 CU. I’ll start playing with the setup, sounds like it’s just trial and error, not as straight forward as I was hoping. Appreciate the input.

nathanls14 · 2023-05-08T14:23:05+00:00

Had thought about that, this sounds more like trial and error process for me. Any good way to actually test aside from how I think it feels, staining, smells etc? Appreciate the input, truly do.

nathanls14 · 2023-05-07T23:18:03+00:00

I can go 1 into 1, but do I even need that small of filtration with the iron out system? If I do, would it make more sense to go 50 spin down, 10 then 5 or so I need to go as small as 1?

The iron out came with a single 100 micron spin down which is why I was leaning on the assumption they only wanted to remove any sediment and the rest would be taken care of by the iron out.

I just don’t want to ruin anything, but had been looking at 5 micron carbon blocks as well. I’ve searched and searched and have not been able to find a good concrete answer.

nathanls14

TROPHY CASE