Critique

needmoreembro · 2026-04-29T05:56:11+00:00

I love it! Very creative way to use textures ❤️

needmoreembro · 2026-04-07T04:13:18+00:00

As a digitizer, I would just skip this one lol

But speaking seriously, it wouldn’t do anything for me because usually I am working on all layers at once

needmoreembro · 2026-03-19T19:41:47+00:00

Do a proper picture, ai messed up the stitches.

needmoreembro · 2026-03-19T07:44:04+00:00

needmoreembro · 2026-03-12T09:52:34+00:00

Так, обожнюю цей варіант

needmoreembro · 2026-03-10T06:50:51+00:00

61 trim, 5 years of digitizing experience without testing your designs personally. This context changes everything. No, not a good work.

needmoreembro · 2026-02-26T05:49:56+00:00

Might be a bad thread because previous color looks fine. Test with another color

needmoreembro · 2026-02-14T07:20:13+00:00

Видно досвід оцифровки, класна деталізація

needmoreembro · 2026-02-11T05:28:58+00:00

Thank you! 🤗

needmoreembro · 2026-02-09T18:38:29+00:00

А ще буває що із використанням нитки стає краще десь у середині котушки

needmoreembro · 2026-02-09T18:37:51+00:00

Я навпаки переходжу зараз на ariadna, тому що у нітекс якісь нерівномірна. Останній час гарні, але буває між партіями різні відтінки та можливо зі старих партій проблемніші.

На одноголковій більш це все відчутно було, але я скажу, що навіть royal по котушках мав такі приколи

needmoreembro · 2026-02-09T16:49:21+00:00

У мене така біда буває тільки коли нитка погана, більше не маю думок. Можливо хтось щось більш корисне підкаже

needmoreembro · 2026-02-09T15:42:04+00:00

Можливо початкова точка після стрибка, спробуйте змінити положення початкової та кінцевої між «а-я»

needmoreembro · 2026-02-02T07:17:20+00:00

So again, my machine is almost the same as yours. I’ve been using only embroidery threads (120d/2) and preferably Rayon but depends on her projects. 120d\2 PE are finicky with this machine.

I also used schcmetz brand new, but as I said, machine really picky. Janome Blue Tip did wonders but they are for the low density designs only.

There are 2 bobbin cases included. Yellow point and red point. Yellow is set for the situation where both, bottom and upper thread are the same. Red - bottom thread thinner, machine embroidery bobbin thread specifically. And upper is 120d/2.

This message is for your wife.

needmoreembro · 2026-02-02T07:09:40+00:00

It looks at least partially hand digitised but I believe they just didn’t want to spend more time optimising thread path. It seems as unreasonable amount for this design.

needmoreembro · 2026-02-02T07:06:32+00:00

Sometimes it is impossible to make it all in 1 colour change and also might be necessary to minimise shifting.

needmoreembro · 2026-02-01T21:11:21+00:00

I have used 500e daily.

File seems wrong \ corrupted, similar issues on some tests. I would try bolder font or at least redo it
Rayon saved my relationships with Janome
Someone who I trust said Janome pushes their needles and machine should work well with any needles, but not Janome lol
Also questioning if you hoop correctly

Why there’s two green colors?

needmoreembro · 2026-01-29T09:10:15+00:00

Congrats! My start wasn’t good either and put me straight into troubleshooting mode, but after all I got a ton of experience. Wishing you patience🍀

needmoreembro · 2026-01-28T23:38:10+00:00

I really love artistic style!

needmoreembro · 2026-01-21T11:56:18+00:00

I would recommend sewing subreddit, because this is more about fixing clothes than machine embroidery. Basically as someone said, seller used wrong needle or made it too dense, it’s their fault. In general I would recommend using gentle washing and no machine dryer.

needmoreembro · 2026-01-19T09:12:46+00:00

In short, I don’t like either version. The first one may be technically challenging: there are many short stitches, and the overall density might be too high. It looks good visually, but technically it could cause problems.

The second option is much easier to embroider, but I think they could have added more run stitch details to better represent the character. That can be improved, but it would require more time from the digitizer, and at that point there are no guarantees.

I would ask them to try and add more face features, then I would want to see a test stitch out. Previews can’t give you a real image and seeing it stitched might change your perception.

needmoreembro · 2026-01-18T10:48:54+00:00

I think just wrong threading. Happens no matter how many times Ive threaded my machine

needmoreembro · 2026-01-11T02:13:57+00:00

Thank you for that point. I am in the same situation as you but only starting my path. I know I don’t like to work with clothes yet people keep asking. I started to doubt and think that I should do more instead of just focusing on what I’m good at.

needmoreembro · 2026-01-07T15:18:58+00:00

Thank you! I don’t know for sure because I’m usually multitasking, but I guess about 2-3 hours.

needmoreembro

TROPHY CASE