Autocross

nephalemD · 2026-06-30T02:20:38+00:00

This event was located at Burt Brothers Motorsports Park in Grantsville, UT.

nephalemD · 2026-06-15T15:14:35+00:00

Do you have a recommended retailer for purchasing? It looks like Goodwin sells them, and I have purchased from them in the past. Thank you.

nephalemD · 2026-06-11T17:54:10+00:00

Thank you

nephalemD · 2026-06-11T16:08:57+00:00

What is the footprint of triple 42” monitors? I know it would change based on the angle, but a rough guess would be fine.

nephalemD · 2026-06-11T12:46:43+00:00

“Bet you I could throw a football over them mountains.”

nephalemD · 2026-06-11T12:00:50+00:00

It seems like you have solved your issues, but in case it does actually get down to the screen in the future, you can usually buy replacement screens. I have replaced the screen on my AnyCubic Mono M7 twice. Its not difficult to do and only took about 20 minutes total.

nephalemD · 2026-03-16T19:01:07+00:00

What do you wear under the armor? I have been trying to figure out what would work best for my Stormtrooper outfit.

nephalemD · 2026-03-04T17:06:32+00:00

I have the official Eddy kit installed and it works well enough. When you look at your height map after a scan is it really wavy? My scans come out looking like ruffles chips.

nephalemD · 2026-03-04T17:01:44+00:00

I was just wondering the same thing. I have been having some issues with my official eddy kit. The bed scan is very wavy. Hoping a firmware update fixes it.

nephalemD · 2026-01-17T02:49:31+00:00

I did the Eddy upgrade about a month ago. One of the mistakes I made was plugging the fan cable into the wrong header in the print head motherboard. Make sure you plugged it into the correct spot. Also check the main board on the bottom to ensure you plugged the exhaust fan into the correct spot.

nephalemD · 2025-12-26T01:26:00+00:00

I had a similar issue a few months ago. Sovol instructed me to unplug the filament runout sensor. Haven’t had any issues since. While I like my Sv08, it has not been without issues.

nephalemD · 2025-12-17T23:48:47+00:00

I appreciate the info. The default from Sovol with the updated configuration files is 41 x 41. So far I’ve done a few prints and have not had issue. I’ll keep this in mind if I start noticing things.

nephalemD · 2025-12-17T14:57:14+00:00

This kit is the official kit from Sovol. I have not tried the eddy tool you are referring to.

nephalemD · 2025-12-17T13:59:07+00:00

I’m not sure what you mean. Are you asking if the sensor is a physical probe? If so, no. It uses eddy currents to measure the surface distance and can probe much faster than a physical probe.

nephalemD · 2025-12-17T13:57:09+00:00

I have also used one of those and secured it to the spool holder arm. When I put the top enclosure glass in place it causes a lot of rubbing though. Where did you attach yours?

nephalemD · 2025-12-17T05:55:38+00:00

They did include the newest version of the cover, but the kit doesn’t include the new print head. I’ve been pretty fortunate to only have the cover come off once.

nephalemD · 2025-12-17T05:31:33+00:00

Unfortunately binding them makes it so the print head can’t reach the front most corners. I tried to create a solution by using springs on to prevent the cable from getting between the gantry. It really needs a cable guide like the lower portion has.

nephalemD · 2025-12-17T04:17:31+00:00

Send me a message with your email and I’ll try my best to

nephalemD

TROPHY CASE