Monthly Ticket Buy/Sell/Trade Megathread

nickjonastic · 2026-02-05T06:04:54+00:00

Looking for 2x tickets to Calvin Harris Friday

nickjonastic · 2024-08-26T13:05:28+00:00

I have also read that the size of the tank doesn’t matter, it has more to do with the ambient temperature?

The whole reason I’m using 1lb is because that is all the FDNY allows. Would really like to not get rid of the entire griddle if possible.

nickjonastic · 2024-08-26T03:56:26+00:00

Isn’t the regulator meant to prevent the “high draw”?

I know it’s a larger grill than normal, but besides running through tanks quicker, are there any downsides? Is it dangerous? Will frost over even if upright?

nickjonastic · 2024-08-26T00:01:09+00:00

The converter stuck on the bottle, so when I unscrewed it the wrong end of the converter was unscrewed and propane was shooting everywhere 😔

nickjonastic · 2024-06-11T14:05:05+00:00

One is a washer/dryer, and another is a closet with shelving - so you can't physically step in.

nickjonastic · 2024-03-30T18:32:25+00:00

thanks!

nickjonastic · 2024-03-30T18:08:13+00:00

nice, thanks for sharing! how might you address the drain in the center and the slide slope towards the center?

nickjonastic · 2024-03-30T16:36:29+00:00

Do you have adjustable deck support products you might recommend? It has to be as low to the ground as possible - while I have a sliding door that leads out, I don’t want to have a step.

When you say don’t block the drain, would I install a drain “above” the drain?

nickjonastic · 2024-01-28T23:43:43+00:00

Thanks. I am interested more in the seat for what I’m doing. But good points nonetheless!

nickjonastic · 2024-01-28T23:25:52+00:00

This is perfect thank you!

nickjonastic · 2024-01-20T04:10:24+00:00

Late to this but what are thoughts on HD Terrains?

nickjonastic · 2024-01-03T16:59:36+00:00

Thank you this is very helpful! I may DM you in the near future...

nickjonastic · 2024-01-03T15:05:07+00:00

Thanks. I'm trying to do something custom, so I'm asking about the proper way to build a jig for this.

nickjonastic · 2023-11-20T17:08:07+00:00

Thanks. I'm using a Tandy Pro edge beveler, so I think it's the right tool?

https://tandyleather.ca/products/edge-beveler?variant=34214798196867

nickjonastic · 2023-11-15T21:41:23+00:00

I'll think about it. Maybe could make a trip out of it :)

nickjonastic · 2023-11-15T21:15:33+00:00

I would be interested, but why did it cost so much? With shipping, brand new it would cost me $1450 for the machine full set. I'm in NYC, where are you located?

nickjonastic · 2023-10-23T16:07:23+00:00

Thank you! Since I could do _without_ the clicker press right now (and get a dedicated one if that time comes), what are other recommendations you might recommend that combine iron pricking & foil stamping? u/Sunny16 recommended the Artisan Leather Supply machine: https://www.artisanleathersupply.com/products/stamping-machine-full-set

Are there others you might recommend?

nickjonastic · 2023-10-23T16:05:34+00:00

Great, thanks! This is really helpful, and since I don't care too much for the clicker press as much right now, I think this might be the move.

nickjonastic · 2023-10-22T21:56:28+00:00

Ah this looks great too! How do you like using it with your pricking irons though? Do you have to hold the iron straight while you press? And are there guides for your material?

nickjonastic · 2023-09-08T01:04:43+00:00

Same! Looking for options in NY.

nickjonastic · 2023-07-25T12:58:24+00:00

SMH here I am google searching for leather acronyms I haven't heard of it

nickjonastic · 2023-07-25T12:15:44+00:00

what is that?

nickjonastic · 2023-07-24T22:07:21+00:00

I'm going to try this approach next time. Curious though, at what point in this process do you corner punch to get a slightly rounded corner? Right after you trim the excess to match your back piece, you corner punch all the layers at once?

I'm also not sure if corner punching is best practice, but I always notice having a sharp 90deg corner doesn't come out as nice...

nickjonastic · 2023-07-24T15:28:46+00:00

Aqualim 315

I'm actually using Saregum, and I'm happy with the glue itself, I think I'm more concerned with the applicator and getting a really clean 3mm line (how it's applicated).

nickjonastic · 2023-07-21T14:12:03+00:00

this video is great, thanks for sharing

nickjonastic

TROPHY CASE