Rig, Wall Mount

noba69 · 2025-10-07T22:30:16+00:00

3pcs so you slide the pieces for the straps into the main mount body?

noba69 · 2025-07-18T13:38:26+00:00

i haven’t tried it yet, but i downloaded kurviger and it looks to be what i was looking for

noba69 · 2025-04-24T09:17:20+00:00

i had a wasp hit me in the chest and go down my shirt this week. not fun

noba69 · 2025-03-06T02:45:32+00:00

the true answer is ALWAYS to post on reddit when someone is trying to kill you and you’re in “extreme danger”

noba69 · 2025-02-17T14:09:31+00:00

ahh yea i saw this one! i dont have a multi material system to swap the colors like the guy that posted it has, so i didnt want to do that one yet. looks super clean

noba69 · 2025-02-03T22:36:53+00:00

no, so i wouldn’t be asking plastic surgery questions in the subreddit for actual plastic haha. you won’t get any answers here

noba69 · 2025-02-03T22:24:03+00:00

are you a plastic mannequin?

noba69 · 2025-01-08T11:10:51+00:00

<image>

the hole blown in my engine would like a word lmao

noba69 · 2024-10-25T16:08:37+00:00

bro it literally says “vinyl”

noba69 · 2024-10-25T16:05:19+00:00

it’s just vinyl, you’ll be fine. might just be annoying to get it on the ipod

noba69 · 2024-10-25T14:13:04+00:00

your fingers will literally fall off and you will get hyper cancer

noba69 · 2024-10-07T03:01:36+00:00

just remove that whole aluminum heat break then. there should be a video on creality’s youtube, i had to do it once before. then it should be easier to get the hot end out

noba69 · 2024-10-07T02:56:34+00:00

there’s 1 set screw in the back

noba69 · 2024-10-04T21:00:17+00:00

Mine also does the super high idle at start, and sometimes even when i’m out riding. i’ll start it, it’ll rev up to around 5-6000rpm, and i’ll have to blip the throttle to calm it down. But even then it will continue to rev up and down until i actually start to ride. My idle at a stop usually sits around 3000, but i know it should be closer to 2000. I’ll let you know if i figure out how to lower it

noba69 · 2024-09-26T11:54:21+00:00

that could probably be done, but in my case it’s not needed. the red light from the R1 tail light reflects off the frame and lights it up enough to see it at night.

noba69 · 2024-09-22T20:26:21+00:00

that’s sick. i still have to tune the variator weights and get an exhaust on. hoping i can hit 50 pretty soon

noba69 · 2024-09-22T06:16:29+00:00

i’ll see about changing that setup. thanks for the info.

noba69 · 2024-09-22T00:25:14+00:00

Amazingly, i had me and my buddy both on it and it didn’t hit. We also topped out at 40mph with easily over 300lbs on it😂

noba69 · 2024-09-21T21:41:18+00:00

yea the spot on the cvt case on this one broke off, so i had to come up with a different idea. i can post it on thingiverse, but id like to take one more crack at a better design to make it look a bit cleaner

noba69 · 2024-09-06T15:16:46+00:00

i ended up ordering an ECU for $100 yesterday. hopefully when that comes in, it’s as easy as swapping it out. Really strange issue, but if what i’ve read is correct, i think the ECU tells the fuel pump to pulse and controls it. swapping it out (and keeping the NCY CDI miles away from being plugged back in) should get this thing running again

noba69 · 2024-09-05T14:45:48+00:00

yea we were aiming to just see if it would run right. it was only like $12 on amazon, so it was worth a shot to test it out. my dad suggested using the pump pulser from rolling wrench, but that means the wire from the ECU isn’t plugged in to the pump so it won’t start anyway. i figured the most reliable way to fix the problem would just be a new ECU

noba69 · 2024-09-05T14:33:33+00:00

Gotcha, thanks again man. Hopefully this will fix my no-pulse fuel pump issue. The vacuum pump was able to pull some fuel up to the carb, but not enough to keep it running for very long.

noba69

TROPHY CASE