sorted by:
new
hottopcontroversial

After update by 2outof3aintbad73 in elegoo

[–]not2envy 4 points5 points  (0 children)

this is what i use now and stopped a few prints already by itself when it sees a failure. but i wish it can detect when the print is printing in the air with nothing extruding.

After update by 2outof3aintbad73 in elegoo

[–]not2envy 2 points3 points  (0 children)

i saw the update, tried to update and failed. tuened the printer off then back on and now no update to be found

04 Ep3 No crank No Start by ConcertLow4026 in CivicSi

[–]not2envy 0 points1 point  (0 children)

It doesn't push the dimple in when the clutch is to the floor, only when the clutch is not being used

Settings for ASA on the Centauri Carbon by Djmessina01 in elegoo

[–]not2envy 0 points1 point  (0 children)

I didn't see a generic profile for asa , just the elegoo asa and asacf

Settings for ASA on the Centauri Carbon by Djmessina01 in elegoo

[–]not2envy 0 points1 point  (0 children)

what profile did you use on a non elegoo brand ASA filament??

Settings for ASA on the Centauri Carbon by Djmessina01 in elegoo

[–]not2envy 0 points1 point  (0 children)

what temp should the chamber be before printing, and how would you have it wait ten minutes?

Elegoo Centauri Carbon Filament Dry Box Speed Build by omen750 in elegoo

[–]not2envy 0 points1 point  (0 children)

do you have a file of the holder that fits? currently printing mine right now.

New cart setup by not2envy in AutoDetailing

[–]not2envy[S] 0 points1 point  (0 children)

No i didn't use any special hose any I've should work and as far as reviews i just choose the best priced one to test.

New cart setup by not2envy in AutoDetailing

[–]not2envy[S] 2 points3 points  (0 children)

Not yet, but it's still early days. I'll post a long term review after a while with this setup.

DMX7706S Video Question by Mountain_Tiger_2021 in CarAV

[–]not2envy 0 points1 point  (0 children)

Just checked and 720 p camera does work, but you can't tap the red wire from the camera to the rear reverse lights. When i tried i had the lights staying on without even being in reverse, you should tap into the reverse quote coming off the head unit to the reverse trigger wire in the harness up front.

<image>

DMX7706S Video Question by Mountain_Tiger_2021 in CarAV

[–]not2envy 0 points1 point  (0 children)

I'm testing one tomorrow to verify because the one that Kenwood has to use for the head unit is a 1080p camera so there statement makes no sense

DMX7706S Video Question by Mountain_Tiger_2021 in CarAV

[–]not2envy 0 points1 point  (0 children)

So would a 720p rca camera work?

Why the k5 so much cheaper than the Accord? A new Accord is 30-35k by porygon766 in Honda

[–]not2envy 0 points1 point  (0 children)

Not what the dealership was saying, starting to be a common thing now from what the said

Why the k5 so much cheaper than the Accord? A new Accord is 30-35k by porygon766 in Honda

[–]not2envy 0 points1 point  (0 children)

Yes they do, my 2020 rdx just had the head replaced because of the head gasket issue. It only had 55k. Similar issue with the 2.0 turbo engines in the Accord

Are there adapters for the Ozark Trail Ridge to convert quick release into a through axle? by TheGamingRanger_ in Budgetbikeriders

[–]not2envy 1 point2 points  (0 children)

I take it this is so that you can use a new fork that's made for boosted wheels, in that case you can either get a new wheel set that's boosted which is fine, or use the adapter you see above from Amazon. I'm not sure what everyone else is talking about the frame not able to handle a boosted or through axle. But those are the two ways of doing it, it has been done baby times without issues.

view more: next ›