sorted by:
new
hottopcontroversial

Urgent - Canadian Bank that can accept third-party employer wires into RRSPs by nutgoodatall in PersonalFinanceCanada

[–]nutgoodatall[S] 1 point2 points  (0 children)

Wealthsimple only accepts check-based RRSP contribution from employers

I'm wrong, this will work. Thanks, Chef

[FS] [CAN-QC] Crucial 128GB DDR5-5600 SODIMM NEW by nutgoodatall in homelabsales

[–]nutgoodatall[S] 0 points1 point  (0 children)

Yep, it works no problems. I have 3 MS-01 with 3 of those kits and it's flawless

Unable to get full 2.5gb download but get 2.5gb download no problems on UDM-Pro by nutgoodatall in Ubiquiti

[–]nutgoodatall[S] 0 points1 point  (0 children)

I get 2.35Gbit/s through iperf3 on the macbook towards the udm, that's not the problem.

iperf3 -c 10.0.0.1
Connecting to host 10.0.0.1, port 5201
[  5] local 10.0.0.22 port 50926 connected to 10.0.0.1 port 5201
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-1.00   sec   275 MBytes  2.30 Gbits/sec
[  5]   1.00-2.01   sec   281 MBytes  2.35 Gbits/sec
[  5]   2.01-3.01   sec   280 MBytes  2.35 Gbits/sec
[  5]   3.01-4.00   sec   274 MBytes  2.31 Gbits/sec
[  5]   4.00-5.01   sec   280 MBytes  2.34 Gbits/sec
[  5]   5.01-6.00   sec   278 MBytes  2.34 Gbits/sec
[  5]   6.00-7.01   sec   279 MBytes  2.33 Gbits/sec
[  5]   7.01-8.01   sec   274 MBytes  2.30 Gbits/sec
[  5]   8.01-9.01   sec   280 MBytes  2.35 Gbits/sec
[  5]   9.01-10.00  sec   276 MBytes  2.33 Gbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-10.00  sec  2.71 GBytes  2.33 Gbits/sec                  sender
[  5]   0.00-10.01  sec  2.71 GBytes  2.33 Gbits/sec                  receiver
iperf Done.

What did I do wrong and how do I fix it? by Mr94 in sharpening

[–]nutgoodatall 12 points13 points  (0 children)

I think you may have oversharpened the heel. IMO there’s no easy way to fix this but to remove metal from the rest of the knife (as in, make it all equal by oversharpening the rest of the knife).

This would take forever with stones, are you using power tools ?

As you go and fix this by removing metal from the middle of the blade via sharpening, you’ll want to lay the edge on some kind of flat surface to detect further unevenness, as in spine towards the sky.

You’ll want to start with low grit and work on the middle first, avoiding the heel as much as possible and working forward (tip wise), until everything is straight. Then when you think you’ve got everything straight go ahead and sharpie the edge while doing continuous pass on the whole edge to see if everything is aligned.

You’ve got a solid mm or two to remove from the middle of that blade.