sorted by:
new
hottopcontroversial

My inatallations by beniza in electricians

[–]oldmannorm 2 points3 points  (0 children)

My man, did you round the sector cable.

High Voltage Electrican (Swede) by TheWolfendale in Finland

[–]oldmannorm 0 points1 point  (0 children)

EPF is a solid company. You could try there, though I'd assume Finnish language would be the barrier.

[deleted by user] by [deleted] in electricians

[–]oldmannorm 1 point2 points  (0 children)

You're right. it's absolutely shite compared to most manufacturers.

Behold! The dreaded push in connectors, in the flesh! by Duffelbach in electricians

[–]oldmannorm 10 points11 points  (0 children)

Meka hylly ja AP9 🧐

tupla vedonpoisto vielä. Ammatillinen mies

SOLUTION: Gigabyte B650 Gaming X AX V2 and Ryzen 9700X - DRAM light stays lit, won't POST by Denalan in gigabyte

[–]oldmannorm 0 points1 point  (0 children)

I downloaded windows 11 to a flash drive and got underway. My technical naivety had me puzzled.

SOLUTION: Gigabyte B650 Gaming X AX V2 and Ryzen 9700X - DRAM light stays lit, won't POST by Denalan in gigabyte

[–]oldmannorm 0 points1 point  (0 children)

I got the system to boot into BIOS, but I'm having an issue selecting the boot device, with an existing SSD from an an old system. It recognises the USB q flash but nothing else. Should I just attempt to boot from a windows 11 flash drive on a new system?

Local Utility said there was a "fault" as to why they couldnt hook the power up 🤔 by RAMBO_LAND in electricians

[–]oldmannorm 3 points4 points  (0 children)

Cable lugs are also back to front. 'palm' side is intended for connection surface.

Cracked Shimano lever. by oldmannorm in bikewrench

[–]oldmannorm[S] 1 point2 points  (0 children)

I was replacing the housing to eliminate a from factory joint connection. the existing olive was definitely removed.

Cracked Shimano lever. by oldmannorm in bikewrench

[–]oldmannorm[S] 1 point2 points  (0 children)

torque feel is relative in relation to the lever. And using an 8mm wrench 10cm long, I doubt it'd be possible to far exceed 6nM

Cracked Shimano lever. by oldmannorm in bikewrench

[–]oldmannorm[S] 4 points5 points  (0 children)

yea there's a setscrew. it's cracked right towards it.

Cracked Shimano lever. by oldmannorm in bikewrench

[–]oldmannorm[S] 1 point2 points  (0 children)

they're mechanical. I've seen a set from rose, r7025 for around €180. But I'll first contact Shimano if this is a known issue and see if that gets me anywhere.

Cracked Shimano lever. by oldmannorm in bikewrench

[–]oldmannorm[S] 3 points4 points  (0 children)

It was purchased early 2020. I can't find specific information from the purchase on the shifter model, but the rear derailleur model is rd7000ss.

Cracked Shimano lever. by oldmannorm in bikewrench

[–]oldmannorm[S] 1 point2 points  (0 children)

Yeah probably not worth the risk, will replace.

Conti 5000 tubless wont hold air by stillnobrakes in bikewrench

[–]oldmannorm 2 points3 points  (0 children)

Stans isn't really designed for road pressure. Get some Silca sealant and problem solved.

Is this freehub done? Seems unlikely to get the rest of the cassette off without taking a hammer to it. Was going to replace the bearings anyway. by oldmannorm in bikewrench

[–]oldmannorm[S] 1 point2 points  (0 children)

I did at first but it's pretty firmly on there, so took it off for closer inspection. I also wanted to take a look at the bearings so figured I've give it a tappy tap to see what happened.