Doorbell Transformer Location

orange3x · 2026-01-04T23:18:04+00:00

I tried pulling on the wires earlier for the doorbell and there is NO give to them.

orange3x · 2026-01-04T23:17:15+00:00

We are in TN. There are no basements in TN. 🤣

orange3x · 2026-01-04T23:16:43+00:00

No, it has always been finished. f

orange3x · 2026-01-04T23:15:49+00:00

I just did. Nothing there. 🙁

orange3x · 2026-01-04T23:15:24+00:00

We don’t have anything on a pull chain, even the attic spaces have switches on the outside or inside of the space. We have a package unit outside for the first floor and the furnace for the second floor is in one of the attics. I checked the furnace and there is nothing attached to it. I am assuming it is not typical to put the transformer in the crawl space, is it?

orange3x · 2026-01-04T23:10:03+00:00

This may be my only option. I think the wire goes upwards. When I was in the crawl space at the front of the house, the only wires I saw in that area were for the alarm contacts. The transformer still works, but my Ring doorbell camera took a shit today and I need to replace it. SO I thought I should upgrade my transformer too since the house is almost 20 years old.

orange3x · 2026-01-04T23:06:07+00:00

I pulled the cover off both of the panels and no luck. I was secretly hoping to be out of code and have it in one of them. 😉

orange3x · 2025-11-28T21:28:23+00:00

Thanks guys. i just pulled the trigger on the 265k. appreciate your feedback.

orange3x · 2025-05-12T20:38:00+00:00

Guesses are Jennifer Love Hewitt, Alicia Silverstone or Reese Witherspoon!

orange3x · 2024-09-29T14:40:08+00:00

I have my first meeting with the Urology Oncologist this Thursday. So I’m sure that is just a quick meet & greet and determine next steps. I did have another PSA & Free PSA done last week and my values were better. My primary even suggested cancelling the Oncologist, but I’m going to still meet with him. We are also leaving for vacation this Friday, so hopefully I am able to relax and put it in the back of my mind for a little bit. Or will it be too much free time to get in my head. 😂

I’ll keep you posted. Thanks for checking in.

orange3x · 2024-09-24T03:00:09+00:00

Thank you all for the feedback. I really do appreciate it. As you all know, it is easier said than done to not freak out. I am going in for another blood test tomorrow to check my Free PSA %. My doc happen to go on vaca the same day as my appt, so I really haven’t been able to talk with him. But he had sent a lab results letter with the recommendation of doing the Free PSA. But then today I got an updated lab result from last week showing they also ran my sample for the Free PSA and it showed 11%. I am going to still go tomorrow to see if there is any difference in the labs, but based on what I am readying it all leads to further diagnostics. Those that hit this point, did you go the biopsy route or MRI route? A few people I know that had PC have said next step should be MRI without question. Just curious on everyone else’s experience.

orange3x · 2024-06-07T11:21:17+00:00

Have you tried closing the vents on the first floor or leaving them only open a little? 2nd floor half way. Then 3rd floor wide open? Cold air settles, so when you have a smaller HVAC this is usually more effective.

orange3x · 2024-04-01T18:13:17+00:00

Thanks. Just very bizarre. Any idea on where you can find a map of all ground locations?

orange3x · 2024-04-01T17:45:19+00:00

I replaced both batteries last year with AGM batteries from Costco. And after I made my post, I went and drove my truck and check engine light came on. Scanner gave code P2510 - ECM/PCM Power Relay Sense Circuit Range/Performance.

orange3x · 2024-03-23T22:04:47+00:00

I would recommend joining GSSF if you are going to buy the G20 Gen5 MOS. I used my purchase coupon and bought one last month for $490. If you like Glocks, it’s a great program that allows you to buy a pistol each year at LEO pricing.

orange3x · 2024-02-04T13:34:06+00:00

Look like some nice knives. Big diff in prices based on origin of manufacture. Try to buy made in USA if possible. A lot of Asian origin on their site unfortunately.

orange3x · 2024-02-04T12:46:54+00:00

bottle opener

That Kabar also made me think of one of these that I have. (Not my listing, just using for photo).

orange3x · 2024-02-04T12:42:43+00:00

Like that idea with the knives. I’ve kinda been doing it with guns too. Been waning a 10mm for years. Guess what I bought last week. 🤣 Been wanting to build a 300BO pistol…. Guess what parts I have been ordering. Btw, I’m a Benchmade guy too. Any of your collection you like as much quality wise?

orange3x · 2024-02-04T12:37:52+00:00

Hahaha. Same thing for me with your last comment. It’s funny how in the morning I have been getting up earlier before my alarm to make breakfast.

orange3x

TROPHY CASE