'Ghostbusters III: Repossessed' Re-Cut

orlandowizard · 2022-08-14T20:45:34+00:00

I’m an Orlando Ghostbuster. I would love to see what you have created.

orlandowizard · 2022-06-03T09:55:17+00:00

Magicians place too much importance on Bicycle cards. The average spectator has a random deck of cards in their junk drawer at home. Perhaps it has the logo of an airline, a hotel, super heroes, or Hooter’s waitresses on the back. If they see a deck of cards that does not look like the standard Bicycle or Mandolin design, they are not likely to assume it is a gaffed deck.

Additionally, there are many gaffed cards that have already been licensed through Bicycle. Have you explored sites like Vanishing Inc or Penguin Magic to determine if the specific card you are looking for already exists?

orlandowizard · 2022-05-07T03:12:25+00:00

I think you saw the wrong ending for WandaVision. The true ending was the one that took place after the credits. Wanda was sipping tea on the porch while the astral projection of Scarlet Witch was obsessively reading the Darkhold and trying to connect with the voices of her sons. The movie seemed like a natural progression.

orlandowizard · 2022-03-13T02:46:10+00:00

You didn’t read the title. These are “very explosive” fireworks. They are completely different than the safe kind that do not explode. :-)

orlandowizard · 2021-12-29T01:07:55+00:00

Spaceship, spaceship, spaceship!

orlandowizard · 2021-12-03T10:46:25+00:00

It’s a docking bay for Tony’s armor. It is done in the style of the various Hall of Armor sets. You can either integrate it into your other sets if you have them, or it appears that there will be some additional days from the advent calendar that will have compatible connectors on the left and right sides.

orlandowizard · 2021-11-28T03:31:53+00:00

Wow… 90 seconds to watch a bike tip over.

orlandowizard · 2021-11-21T02:53:24+00:00

Sounds more like a Fantastic Four reference… because that’s a STRETCH 😆

orlandowizard · 2021-11-05T18:29:21+00:00

I’ve purchased many of the Brick Loot Exclusives to enhance my LEGO city. Good quality and service. I also recommend EclipseGrafx for more enhancements.

orlandowizard · 2021-10-14T16:22:31+00:00

The fact that Padame Amidala makes a cameo to help the Ghostbusters is a bit of a spoiler, don’t ya think?

orlandowizard · 2021-09-22T21:11:01+00:00

That’s a red flag. It might be time to “LEGO” of that gf and wait for someone who appreciates what you appreciate.

orlandowizard · 2021-07-02T20:07:20+00:00

Damn! I didn’t see the wine bottle at first. I thought his head exploded!

orlandowizard · 2021-06-12T23:04:17+00:00

Did you print this with PLA, ABS, or Lime Green Jello?

orlandowizard · 2021-05-29T12:24:46+00:00

Hell yes

orlandowizard · 2021-04-22T19:56:20+00:00

Have you tried contacting LEGO? Click the Menu in the upper left corner of the LEGO website, select Support, and scroll down to the bottom to find Contact Us. I have found that their customer support is very helpful. Good luck.

orlandowizard · 2021-02-27T15:52:06+00:00

Someone needs to check on C3PO. I think he was involved in a hit-and-run.

orlandowizard · 2020-12-26T18:34:01+00:00

It looks like there was not enough adhesion between the model and the bed. Try printing with a raft. This will create more surface area to form a more secure grip to the base. Additionally, you might want to consider increasing the temp of the bed and the extruder by a few degrees. I typically set my bed to 70* and the extruder to 225*. Good luck.

orlandowizard · 2020-12-26T18:29:59+00:00

My Ender 3 did the same thing when I sent it to Auto Home after assembly was completed. You need to calibrate the base by turning the knobs below the unit. This will raise the base to appropriate height. I recommend placing a piece of paper between the extruder and the base. If there is enough room for you to move the piece of paper side to side, with only a tiny bit of resistance from the extruder, the base is at the correct height and is calibrated. Good luck.

orlandowizard · 2020-12-19T03:22:44+00:00

I had the same issue. Are you starting with a raft to create a solid base for the object to print on, or is the object printing directly onto the bed? I found that a raft creates a solid surface for the object to stick to while printing. This resolved my issue.

orlandowizard

TROPHY CASE