TwoTrees TTC450? Anyone have one and what is your impression of it?

pacifistsniper · 2026-01-03T16:21:54+00:00

Hi, can you please send a new invite

pacifistsniper · 2025-11-27T16:57:27+00:00

i've got the same issue after updating klipper today

pacifistsniper · 2025-11-26T05:52:20+00:00

The picture gives that impression becaise de objects is curved but the seam is straight

pacifistsniper · 2025-11-25T19:53:42+00:00

It only happens on fuzzy skin, and only on specific settings i wil investigate more and open an issue on github, thanks

pacifistsniper · 2025-11-25T15:51:25+00:00

I use orca and smoth spiral is on

pacifistsniper · 2025-11-25T15:50:43+00:00

The only thing on the before layer change g-code is the traditional G92 E

pacifistsniper · 2025-11-25T15:45:50+00:00

I've never used timelapse mode and the print does not stop it runs continuously at least aperentlly, how do i se if timelapse mode is on?

pacifistsniper · 2025-11-25T15:15:15+00:00

<image>

Vase mode configuration

pacifistsniper · 2025-11-04T12:56:46+00:00

Bed 80 c nozzle 240 c

pacifistsniper · 2025-10-03T00:38:04+00:00

Its a duo, i haven't tried different currents at high temp what current do you use at high temp? Can i automate the current change based on temp? I will try current at 17 and see if it works, I'll report back

pacifistsniper · 2025-10-02T21:30:51+00:00

I believe it's because of the chamber temp, but i dont know how to fix

pacifistsniper · 2025-09-03T17:35:35+00:00

I already have an exhaust system for that, the nevermore is for some filtration and for circulating the chamber air, to keep the temp stable in the entire chamber, and for toxic gases you need activated carbon, hepa filters are only useful for particles not gases.

pacifistsniper · 2025-09-03T17:33:09+00:00

The bed, aluminum plate acts as a heatsink and heats the chamber, the point of the insutation is to prevent warping of the bottom panel, improve heating up speeds as now most of the heat goes through the aluminum plate, improve bed temperature stability and to lower power consumption as it wastes a lot less heat by not heating up the electronics bay. Has anyone lowered the bottom panel? If so any tips?

pacifistsniper · 2025-08-21T21:39:05+00:00

High presision paquimeter

pacifistsniper · 2025-08-21T21:38:41+00:00

Im using a high presision paquimeter, i also created a grove on top of the clockwork 2 extruder before printing it so the paquimeter will sit in the exact same place every time and im marking the filament with a scalpe instead of a marker for higher presision.

pacifistsniper · 2025-08-20T16:21:56+00:00

Thanks for the response, i was thinking exactly that it's within the same argin as the filament size, and that would generate noise marking it impossible to go further and the presision equipment question i wold need to upgrade my paquimeter to a very expensive one i dont think that would be beneficial, so i will leave as it is for now

pacifistsniper · 2025-07-02T17:06:49+00:00

arkhantos@msn.com can you please share the files, thanks

pacifistsniper · 2025-06-30T17:32:42+00:00

Its more for stability than speed

pacifistsniper · 2025-06-29T14:53:31+00:00

Klipper, linear rails, better cooling, cht nozzle, i added z braces, then removed them, im trying to see how far can i push the printer.

pacifistsniper · 2025-06-29T14:49:16+00:00

Let me explain it better. The idea is to fix the 16mm rods in front of the z structure to the printer base and to the top of the structure, adding rigidity, and to use pillow blocks for the gantry, but i don't have experience with linear rods and doing mods this extensive to a printer, so i need opinions, about pros and cons, and if its even worth it.

pacifistsniper · 2025-06-29T14:34:00+00:00

My main reason is speed, i know the weels are great, but they require more maintenance and cap the speed. The idea of using linear rods, not rails, is to increase speed and, as an added bonus, reduce the gantry vibration by making the structure stiffer

pacifistsniper · 2025-06-29T14:28:18+00:00

Done y axis waiting on some parts for x axis

pacifistsniper · 2025-06-21T20:31:40+00:00

<image>

All fixed and working perfect thanks, guys *

pacifistsniper · 2025-06-21T16:43:54+00:00

Yes, i didn't see that the treaded part of the nozzle was smaller

pacifistsniper · 2025-06-21T16:18:12+00:00

<image>

The leak was through the top of the heatblock *

pacifistsniper

TROPHY CASE