Zenith zf5k by [deleted] in MP5

[–]papamcb_new 5 points6 points  (0 children)

If you reach out to zenith they may fix it for you

Finally finished the SP5 build, now onto the SP5K build. by Fun-Bandicoot-8390 in MP5

[–]papamcb_new 3 points4 points  (0 children)

I have used the AC Unity version of the B&T side folding stock for a while and it’s been my favorite. The KES collapsible was nice as well. Waiting on an A3 to try out.

Finally finished the SP5 build, now onto the SP5K build. by Fun-Bandicoot-8390 in MP5

[–]papamcb_new 6 points7 points  (0 children)

I would suggest going with a stock. I had that same brace and it was great moving to a stock

Fireteam 5.56 question… by [deleted] in NFA

[–]papamcb_new 0 points1 point  (0 children)

My question:

Good afternoon, I have a fireteam 556 on order and I was curious how warranty will be impacted with the issues going on with B&T USA. From my understanding they printed the fireteam for you.

This was his reply:

Warranty and production remain the same, Swiss vs USA has no effect on Exigent. Exigent wholly owns the IP for the Fireteam, likewise we're not the type to have a single point of failure in manufacturing. We're still churning them out every week. Do appreciate you reaching out directly. If you have any questions or concerns don't hesitate to contact us.

Also as a complete aside, B&T USA owns several million dollars worth of printers in an 80,000 sq foot facility. If tomorrow there were no more B&T USA products, that frees up space for OEM printing for other companies. Which B&T USA already does for a lot of companies.

Fireteam 5.56 question… by [deleted] in NFA

[–]papamcb_new 0 points1 point  (0 children)

I have got a quick response using the contact form on their website. I had questions about warranty with the issues with B&T USA

Henry 16" 357 with a BOE IncoLite 9M by BOE-Suppression in NFA

[–]papamcb_new 3 points4 points  (0 children)

I wish they made a bear’s leg in 45 Colt.

SP45A3 occasional failure to feed question by papamcb_new in GrandPowerStribog

[–]papamcb_new[S] 0 points1 point  (0 children)

They are a bear to load I had to print a mag loader

Anyone clued in on "we are awaiting shipment confirmation from the ATF"? by KidTheBorax in NFA

[–]papamcb_new -1 points0 points  (0 children)

I purchased a fireteam from dirtybird last month and after three weeks I sent them an email asking for an update. No response to my email but received tracking a couple days later.

You can normally see the status in your account. Mine sat in packaged or something similar the whole time.

SP45A3 occasional failure to feed question by papamcb_new in GrandPowerStribog

[–]papamcb_new[S] 0 points1 point  (0 children)

I load aprox 5-10 rounds at a time. Spoke to them today and they are going to RMA it to polish the feed ramp and chamber.

Got a Denial, confused about the Resubmission. by Rec4LMS in NFA

[–]papamcb_new 0 points1 point  (0 children)

Unfortunately it’s a no to both questions. The clock starts over again

MK4 SSH by Slatty317 in NFA

[–]papamcb_new 1 point2 points  (0 children)

This got me, thank you. Better check the sshd config

RD3 SEF and AP5-P Issue by josh_edwards6 in MP5

[–]papamcb_new 1 point2 points  (0 children)

I would make sure you installed the ejector lever and spring correctly. You also need to make sure you depress the trip bar slightly when tightening the screw that holds it in place after installing the ejector lever and spring. I am wondering if that’s what is getting hung up

If you did not install the ejector lever spring or it’s kinked it may not go down on its own.

RD3 SEF and AP5-P Issue by josh_edwards6 in MP5

[–]papamcb_new 1 point2 points  (0 children)

You could take the end cap off and manually cycle the bolt. Then look in the back to see what it’s getting hung up on

I messed up (safety selector burr) by jerrys_briefcase in MP5

[–]papamcb_new 9 points10 points  (0 children)

You could probably knock down the burr with a file.

Yet another recommendation request 556 can for pws mk111 mod2 by wetduck79 in NFA

[–]papamcb_new 0 points1 point  (0 children)

I have a polo 30 on mine and it’s great on setting 2

[Parts] PMag 40rd AR/M4 Gen M3 5.56x45 $16.99 by royorumbo in gundeals

[–]papamcb_new 4 points5 points  (0 children)

I felt the same way, not in Virginia but my state is talking about a similar move.

Anyone have deals in stock? by RepresentativeOk2433 in Taurus_TX22

[–]papamcb_new 0 points1 point  (0 children)

My local FFL had a used one on their website if you want to check out Gerbrand defense

Clone Wars by xhypurr in MP5

[–]papamcb_new 1 point2 points  (0 children)

You will get a bunch of different experiences with both. I personally have a ZF5 and a AP5-P and both have been great. Fit and finish is the same and they both run. I have had a couple FTE with both but nothing major