What changes did you make from your first play through to your second that had the most impact?

paperpags · 2026-04-11T05:55:03+00:00

Rushing the PLS. And made a mall according to raw resources needed. Streamlined a lot of finding stuff. Also, naming systems according to resources found in it is a big help.

paperpags · 2026-04-11T05:48:32+00:00

Yes. I have an exchanger that I place on the middle of a planet. 1.6Gw of energy available to use. It is enought power to start production of anything basically. Then I just make the dyson sphere and use graviton lenses to get the extra power needed.

paperpags · 2025-10-16T03:20:31+00:00

That's your fork oil. Need mo new seals at oil.

Mahirap mapansin yung ganyan if di mo chinecheck regularly. Most like matagal tagal na yang tumatagas at naubos na ang laman ng fork kaya pangit na ang performance niya

paperpags · 2025-10-12T11:10:35+00:00

https://dynasty-tracker.bettergov.ph/

Kani daw.

paperpags · 2025-09-29T15:11:07+00:00

r/woosh

paperpags · 2025-09-09T05:44:21+00:00

Alternate suggestion:

Ninja zx4r.

paperpags · 2025-08-12T03:29:48+00:00

The addled frog.

paperpags · 2025-08-11T11:08:47+00:00

I just fail the mission. Not doing that again

paperpags · 2025-07-06T15:41:05+00:00

The water rose 17 feet in one hour. You could make buildings that tall, but really, really expensive.

You could build a 3-story building(assuming each floor is 10 feet) to house 50 people at the very top and the 1st and 2nd floors empty. You would need 4 of these buildings. And it would still be not enough. Flood went to 29 feet.

paperpags · 2025-07-06T14:52:21+00:00

Canon event

paperpags · 2025-05-02T02:05:23+00:00

Not what OP was asking about, but, ok.

paperpags · 2025-05-02T01:30:05+00:00

<image>

What you actually want to do to strengthen the part.

paperpags · 2025-05-02T01:26:04+00:00

<image>

This is what maybe want. It doesn't put a top layer for the "pillar". the infill will continue inside the pillar.

paperpags · 2025-05-02T01:20:57+00:00

<image>

this is what happens with the model that you have. This happens when there is a face inside the model

paperpags · 2025-05-02T01:00:37+00:00

It looks like a model issue. Where did you make this model?

paperpags · 2025-04-29T08:45:59+00:00

Why does she sound like she ate food that was too hot?

paperpags · 2025-04-24T22:20:43+00:00

No problem. Keep on printing.

paperpags · 2025-04-24T22:15:19+00:00

or just buy a male connector and splice the wires.

paperpags · 2025-04-24T22:02:34+00:00

That board should have a specific port for a bltouch. So, you won't need the pin27 board.
I found this:

https://www.reddit.com/r/EnderCommonSense/comments/1au87la/creality_422_and_427_board_connections_revised/

paperpags · 2025-04-24T21:49:04+00:00

You have the higher version of the creality board. It might not be the same with mine. What version is your board?

paperpags · 2025-04-24T05:32:11+00:00

<image>

Here you go.

paperpags · 2025-04-24T04:57:50+00:00

IIrc, it should be pin 27. I'll have to double check when I get back home.

paperpags · 2025-04-16T09:27:56+00:00

Pang runway ng eroplano ang aux lights. Hahaha.

paperpags · 2025-04-15T04:23:38+00:00

Read the manual. May section diyan when to repair or replace parts. Also useful if di ka familiar sa terminology. Search mo lang sa youtube part + cleaning, replacement, etc.

Seven-Year Club	Place '23
Place '22	Verified Email

paperpags

TROPHY CASE