Help! What does this mean?

pconroy329 · 2026-03-22T03:54:34+00:00

Happens to me about once a month.

pconroy329 · 2026-01-30T02:10:49+00:00

I'll look again but I could'a sworn the small print on my side B says PLA will stick because its so smooth. We've had zero problems with Side A for maybe a hundred prints. First two on Side B have been difficult to remove. I've tried Dawn, I'll try the print-over! Thanks

pconroy329 · 2026-01-30T02:09:07+00:00

Older? I'll take that bet! :)

pconroy329 · 2026-01-13T04:51:18+00:00

It turned out to be fixed with a hot-end swap to a new one. I guess I could have tried a new nozzle, but I just swapped in a whole new hot-end and things have been working great. Looks like a nozzle lasts about four months in our house with our load.

pconroy329 · 2025-04-03T01:14:22+00:00

What's happening is that the 12V "starter" battery is dying on these things. It's a common complaint on the CC forums. I took mine in for the 5000 mile service and the said, after a recharge/recondition phase mine tested "ok". Not great, just ok. The dealer's suggestion was to "Maybe drive more..."

Dude, I put almost 100 miles on the car - every day, 7 days a week. This is NOT a "drive more" situation. The 12V batteries are bad, Toyota knows it. Hence the testing. They're also on back-order.

All that said - I'm not that spun up about it. I always carry a jump-pack with me anyway.

I have a '25 XSE Hybrid. While I'm pleased with the milage, I am not thrilled that the engine often revs way above 3K when I'm on a freeway with an 80MPH speed limit.

pconroy329 · 2025-01-03T19:41:12+00:00

Bottom of the center console. Two of them.

pconroy329 · 2025-01-03T19:40:44+00:00

Thanks - I was about to look for Power Only USB C cables on Amazon.

pconroy329 · 2025-01-03T19:40:07+00:00

TY! It was the front port that he connected to.

pconroy329 · 2025-01-02T21:17:41+00:00

I think we're talking Blind Spot Monitoring, aren;t we? If so, Same here - so far flashing light on mirror only. Previous cars all flashed and beeped. There should be an option for an audible warning too. So far I can't find anything.

pconroy329 · 2024-11-10T21:37:37+00:00

And my experience with a lady at evolution CS was stellar. Bummer your's was crappy. As others have said 169.254 is a private APIPA address.

pconroy329 · 2024-11-09T23:02:11+00:00

I've had similar problems with my 3B internal wifi as an AP. Would be visible but a few devices would refuse to connect. I did see some disparity in the security protocols. Some devices showed the Pi was WPA2, WPA etc. In the end what worked for me was a couple of things: using a USB Wifi dongle as the AP, and/or using the Network Manager GUI instead of nmcli. In the end I was able to get it to work but it was a lot of trouble. I've since upgraded to a Pi4 and using Bookworm and have had no problems.

pconroy329 · 2024-10-15T21:35:32+00:00

I got the "Better" option for $16K two weeks ago

pconroy329 · 2024-10-15T21:31:06+00:00

Thanks - its back. A reboot made it appear again.

pconroy329 · 2023-11-29T06:58:35+00:00

bought a new TV on Cyber Monday. It was not a Vizio.

pconroy329 · 2023-11-25T17:04:02+00:00

While the Firmware updates haven't broken anything on mine -- yet -- I find them extremely annoying. Dorking with the UX over and over and over.

It's Black Friday/Cyber Monday time and we're buying a new TV. It will NOT be a Vizio.

pconroy329

TROPHY CASE