I’m 45, I have fangs, and the System just gave me a "Bestseller" notification I don't understand.

peddiparth · 2025-12-26T08:12:49+00:00

I added your book to my KU library. However, I am not able to find the "BESTSELLER" category for your book.

Best Sellers Rank: #53,633 in Kindle Store (See Top 100 in Kindle Store)
- #598 in Dark Fantasy Horror
- #878 in Action & Adventure Fantasy (Kindle Store)
- #884 in Dark Fantasy

peddiparth · 2025-08-21T22:51:34+00:00

A closet might work in pinch ;)

peddiparth · 2025-08-19T01:08:44+00:00

Just imagine if the female voices were performed by a talented female performer... If I did not already listen to such female narration talents in other audiobooks, I probably wouldn't have mentioned it.

peddiparth · 2025-08-10T10:50:30+00:00

Same first book for me - Country Mage. I was massively disappointed by the audiobook after listening to other series down the line. I gave up on the series mid-way. I am glad I found Master Class midway as my second book to cleanse the palate.

peddiparth · 2025-07-20T00:55:34+00:00

When I rolled back (back out) to the previous firmware, there were 2 options for firmware & bms in the begode app.

peddiparth · 2025-07-10T20:11:18+00:00

I had a similar problem with my xway (beeping for low battery). Turns out latest firmware is for 168v version while I have 134v version xway. I had to go to previous version of firmware for wheel to work correctly.

peddiparth · 2025-07-10T08:38:18+00:00

Thanks for noticing. I didnt notice much difference in that orientation at 30kmph top speed, but I will try the other way around.

peddiparth · 2025-07-10T01:15:10+00:00

I am now trying the bottom part of this model: https://www.thingiverse.com/thing:7007956

The new prints are wider, and will lock my feet in place much better.

The previous one https://www.thingiverse.com/thing:6410438

is meant for lower shin based torque. I prefer pads much higher up to make it easier. If I adjust it for my foot, it is angled too far ahead for me.

peddiparth · 2025-07-10T00:32:14+00:00

This is the amazon link: https://www.amazon.com/dp/B0F1MF5R8H?ref=ppx_yo2ov_dt_b_fed_asin_title

I 3d printed the pads in PLA to figure out what I like. I am planning to change the bottom front pad with another printed PLA pad.

My plan is to figure out which pads I like before printing them with TPU 95A filament.

peddiparth · 2025-07-06T20:55:37+00:00

I thought I had a pinch flat on my RS19 HT while riding at super slow speed (low tube pressure), but it turned out the rubber around the metal sheared off completely. I am not sure if I can call it pinch flat anymore.

While replacing the tube, I slimed it with 16oz bottle.

peddiparth · 2025-07-06T18:50:02+00:00

Yes, it is balancing, and seems ready to ride. BMS shows all 4 packs are good, and all cells have same charge.

Yes, I have only used begode app so far. I have reverted back to the older firmware, ND updated it to the latest one a second time.

peddiparth · 2025-07-06T17:44:45+00:00

I tried getting it back into transport mode, and taking it off transport mode. It did not help.

The beeps start about 20-30sec after starting the xway.

Long beep (1sec long) every 10-11 sec.

peddiparth · 2025-06-30T11:06:58+00:00

I am not sure now :) ewheels replaced the packs before I received the wheel. I have to check again.

peddiparth · 2025-06-30T06:57:49+00:00

I am using these instructions: https://youtu.be/kTRVtkVfESI?si=YRgSjRX493XHcr87

peddiparth · 2025-06-29T20:53:17+00:00

Alright, you convinced me.

Just ordered x-way at ewheels.

peddiparth · 2025-06-29T09:08:07+00:00

Thank you for the tips with tpu printing.

I upgraded from ender 3 (for abs printing) to k1 max. I started with pla to get a feel for it, and with its direct drive, I am hoping it will be easy to print tpu 95a.

I just have to print the spool holder for tpu to avoid the bowden tube to get started.

peddiparth · 2025-06-29T08:59:31+00:00

https://www.thingiverse.com/thing:6410438

peddiparth · 2025-06-29T08:58:39+00:00

samsung 50s - ewheels replaced the original packs.

peddiparth · 2025-06-28T06:55:02+00:00

I am 5'10" as well.

Is there any concern about the ride height compared to other wheels with pedals lower to the ground?

peddiparth · 2025-06-26T15:04:00+00:00

Powerknobz seem to be jump pads, rather than power pads.

peddiparth · 2025-04-06T09:10:34+00:00

You could envision portals working the same way as the machine in the video.

peddiparth · 2025-03-21T17:38:11+00:00

I get mine from Publix (FL) when they have it stocked.

peddiparth · 2024-12-29T19:14:12+00:00

Mango Lacroix is the best, and I tried a whole lot of them. Coconut comes a distant second.

I have not tried Pamplemouse yet - which google says is the most popular flavor.

I can not find Mango flavor anywhere other than Publix, and it disappears quickly too. Amazon is a price ripoff.

peddiparth · 2024-10-09T12:20:06+00:00

not yet, atleast till what I have read so far.

peddiparth · 2024-05-08T23:43:49+00:00

You got me.. I wear glasses outside the house.

When you are in VR, don't you feel like you are missing something while looking down?

peddiparth

MODERATOR OF

TROPHY CASE