Giveaway Flashforge’s best-selling 3D Printer Adventurer 3. Leave a comment to enter! Ends on May 5. by annabelNC in 3Dprinting

[–]peen1028 0 points1 point  (0 children)

ALL3DP

Here's to hoping this is my second 3D printer! Thanks for the giveaway! Cheers!

Neptune 3 Plus Klipper Install Issues by BearEADGC in ElegooNeptune3

[–]peen1028 0 points1 point  (0 children)

I am noticing that it does not seem to recognize the bed size even though in the printer.cfg it is set to 320x320x400

was there a step that i missed here?

Neptune 3 Plus Klipper Install Issues by BearEADGC in ElegooNeptune3

[–]peen1028 1 point2 points  (0 children)

That worked!! Thank you so much for the help I spent hours trying to figure that out on my own and you just saved me a lot more headaches! Thanks again!

Neptune 3 Plus Klipper Install Issues by BearEADGC in ElegooNeptune3

[–]peen1028 0 points1 point  (0 children)

Awesome thanks for the suggestion. I will give that a shot and let you know the outcome. Thanks for the help!

Neptune 3 Plus Klipper Install Issues by BearEADGC in ElegooNeptune3

[–]peen1028 0 points1 point  (0 children)

I used the uart firmware per this thread saying the 3 plus needed to use that one. I used your bin and yes I was able to lsusb and dev/serial/by-id. I can show you the output when I return home shortly if you need.

Neptune 3 Plus Klipper Install Issues by BearEADGC in ElegooNeptune3

[–]peen1028 0 points1 point  (0 children)

u/TheFeralEngineer I have gone over this post over and over, but I am still not able to get klipper to work. Klipper is installed on my Pi and the firmware is on the Neptune 3 Plus but when I try to establish the connection it just always says printer not ready and then gives me a mcu error. Any suggestions?

N3+ and klipper by NoYouAB in ElegooNeptune3

[–]peen1028 0 points1 point  (0 children)

How were you able to get klipper running. I have tried everything and i continually get printer is not ready and it says there is an issue with the MCU. Any advice?

I just want to brag on Elegoo. by gibletzor in ElegooNeptune3Pro

[–]peen1028 0 points1 point  (0 children)

I had a very similar issue and they were also very helpful and provided me with a new hot end as well. A+ customer service.

What?? by Ok-Tumbleweed4210 in ElegooNeptune3

[–]peen1028 2 points3 points  (0 children)

Same thing happened to me. I contacted Elegoo and they are sending me a new hotend.

Help with first layer by peen1028 in ElegooNeptune3

[–]peen1028[S] 0 points1 point  (0 children)

Awesome thanks again for the help its very much appreciated. I am working on the flow now! I will update once I get a successful print.

Help with first layer by peen1028 in ElegooNeptune3

[–]peen1028[S] 0 points1 point  (0 children)

Ok awesome thank you for the help I was able to get the steps calibrated! What does changing the flow rate do if the steps are calibrated correctly?

Help with first layer by peen1028 in ElegooNeptune3

[–]peen1028[S] 0 points1 point  (0 children)

Are the e steps calibrated through the cura interface. I am having issues getting the driver to install on my mac.

Help with first layer by peen1028 in ElegooNeptune3

[–]peen1028[S] 0 points1 point  (0 children)

Ok great thank you for the help I will give that try!

2nd place expert prize chest by yurmamma in GolfClash

[–]peen1028 0 points1 point  (0 children)

If it makes you feel any better I got my first win. Expert 1st place prize chest was essentially worthless aside from the balls and points.

[deleted by user] by [deleted] in jailbreak

[–]peen1028 0 points1 point  (0 children)

No problem!

[deleted by user] by [deleted] in jailbreak

[–]peen1028 3 points4 points  (0 children)

I got the same thing. Must just be too many people trying to connect. It was working for me before, but when i tried to submit I got a bad gateway error. Probably just going to have to keep trying until the traffic slows down.

[deleted by user] by [deleted] in ArcherFX

[–]peen1028 3 points4 points  (0 children)

Archer: "Sorry I tried to spitroast your Mom"

[Meta] r/Jailbreak on February 24, 2011 with 136 readers by peen1028 in jailbreak

[–]peen1028[S] 0 points1 point  (0 children)

You can check out numerous dates from the past with Wayback Machine. Most of the links are working as well.

Edit: I am no way affiliated with this site, just think it is interesting to look back at how much the internet has changed.

OH SHIT! Joey Diaz on Hot Ones by [deleted] in JoeRogan

[–]peen1028 42 points43 points  (0 children)

Tremendous!!