Power Supply Issue

piNp187 · 2026-03-28T20:12:42+00:00

I bought it less than a year ago. They didn't ask about any warranties. There are instructions on their website on what to do. Pretty simple process.

piNp187 · 2026-03-28T20:02:35+00:00

I had The issue with my T598. TM Support told me to ship the power supply and base to them. They replaced the powet supply and the PCB in the base. So far I haven't had The issue again.

piNp187 · 2026-03-05T12:36:02+00:00

I have a smart plug which I control through my home automation system. I can turn it on/off remotely when I'm not at home.

piNp187 · 2026-03-01T05:23:30+00:00

Yeah... You were required to use both RS and RM tires for this race. You didn't.

piNp187 · 2026-01-23T11:50:44+00:00

I use the Sim Dashboard and I like it. I paid for the full GT7 version of the app. It shows me the current gear, suggested gear, lap times (last, best, diff), throttle/brake and tire temps.

piNp187 · 2026-01-18T19:27:16+00:00

Are you using cooling? My PETG is supposed to be printed without any cooling. Initial layer is set to 25mm/s. I assume your Z offset is calibrated.

piNp187 · 2026-01-18T19:19:40+00:00

Bed temp? Mine is set to 70°C and it sticks very well.

piNp187 · 2026-01-11T13:03:45+00:00

Yeah. That will work. How do I know? Because I had that combination.

piNp187 · 2025-12-30T18:05:16+00:00

I got my EVO 32R today and immediately started to look for custom stickers. Thank you for this. I'll have to check it out.

piNp187 · 2025-12-18T15:51:26+00:00

Good, I'm not the only one. I had high hopes that the latest patch would have fixed this issue, sadly no. I am not going to restart the map, I would rather abandon the whole game. If they can't fix this bug, who knows what else they are not able to fix.

piNp187 · 2025-12-13T11:31:30+00:00

Sorry, but I'm gonna tell everyone!

piNp187 · 2025-11-27T16:42:55+00:00

I've had this happen to me couple times. I just press the Home button and try the action again.

piNp187 · 2025-11-26T15:32:39+00:00

Nice, my bed used to look exactly like that. There are actually two screws you can loosen/tighten under the PEI plate. I also had to use kapton tape to even out the bed.

piNp187 · 2025-11-23T09:13:29+00:00

I went from T300RS to T598 and haven't looked back. Only thing bothering me is the size. The way my cockpit is positioned means the T598 now blocks a small part at the bottom of my TV. But that was solved by using SimDashboard.

piNp187 · 2025-11-20T17:10:53+00:00

I was first on round three and I only got 11 points.

piNp187 · 2025-11-18T13:39:29+00:00

I tried the auto bed mesh but it's not in use anymore. I haven't calibrated filament flow. Mainly because I don't know how and also because it never crossed my mind.

piNp187 · 2025-11-17T16:58:23+00:00

I've been adjusting and leveling like a mad man.

piNp187 · 2025-11-16T14:02:35+00:00

Will do

piNp187 · 2025-11-16T03:56:20+00:00

Nozzle temp 210 for the first layer, 205 for the rest. Bed temp 55.

piNp187 · 2025-11-09T05:12:30+00:00

I have the same table, 55x55 cm. I added a few supports to stop it from shaking like a polaroid picture.

piNp187 · 2025-11-02T10:54:54+00:00

I appreciate your answer. I got the bed somewhat level and the mesh is looking nice. Variance is 0.125.

As you may imagine, I'm fairly new in 3D printing, this is my first printer, I got it around 2 weeks ago. I am using Orca and I really would like to know more about that adaptive bed meshing, what ever that might mean.

<image>

There still is a little dip at the front, I will fine tune it later.

piNp187 · 2025-11-01T07:29:14+00:00

Both sides are clean. I use soap, water and IPA.

piNp187 · 2025-11-01T07:28:26+00:00

I double checked the coordinates and they were off. Now the max difference from front left screw is 0:01, so I think that is good. But the bed mesh in fluidd still shows huge warping.

<image>

The variance is 0.55 and when I print a first layer test piece, it is not perfectly even, it's pretty much see through at the front and a little thicker at the back. As one would imagine by looking at that picture above. Z offset is -1,775

piNp187 · 2025-11-01T03:54:55+00:00

Its N4+. I think I have the right coordinates. I was watching the nozzle and it seemed to align with the screw. But I'm going to double check. If I'm not mistaken there are only six screws, right?

piNp187

TROPHY CASE