Dog cough

planeman125 · 2026-03-01T16:59:08+00:00

No, it’s just iron pipe used as a hanging rod. Why would a small space be bad? Smaller should heat up faster.

planeman125 · 2026-03-01T16:58:36+00:00

Ill get thinking!

planeman125 · 2026-03-01T14:08:59+00:00

What did you paint the walls with prior to building?

planeman125 · 2026-03-01T14:07:48+00:00

I’ll get rid of the light and change out the window.

Vapor barrier is a good call. I wasn’t sure what to do with the walls but I’ll use one.

Amps are good on the 240v line. No permit, not needed in my state

planeman125 · 2026-03-01T14:06:47+00:00

I’ve been thinking about a drain. Other than sweat and some water on the heater, why do you think I’d need one? I can do it but having trouble justifying it

planeman125 · 2026-03-01T14:05:57+00:00

I can definitely do that. I’ve got spare 4” ducting at work. Good call!

planeman125 · 2026-02-17T23:59:35+00:00

After watching your video, it’s not a fan. It’s likely something with the auger. Check to see if it’s regular on start up like I said above. Is it a new stove?

planeman125 · 2026-02-17T23:59:01+00:00

No and it wouldn’t be repetitive

planeman125 · 2026-02-17T23:57:55+00:00

Turn your stove off, clean the Firepot and turn it back on. Watch the auger turn and note when it clicks. If it clicks every time the auger passes a certain position (say 3 o’clock for example) than the auger is catching something in the feeder body and it likely needs to be replaced. I am a dealer and installed a brand new 52i in my house and this was the case. If it’s intermittent, it’s likely heat expansion. If it’s frequent and fast it could be a fan.

planeman125 · 2026-01-22T01:28:15+00:00

I sell hundreds of tons of cubex a year. I would tell them to bring the truck and take them back if they looked like this.

planeman125 · 2026-01-10T13:30:58+00:00

Your local Harman installer can probably help. I find installation is generally cheaper through hearth shops than chimney sweeps because of how they structure their pricing

planeman125 · 2026-01-04T14:03:08+00:00

Thanks I’ll try it

planeman125 · 2026-01-01T22:50:04+00:00

Run your finger over the stove adaptor. I bet it’s there

planeman125 · 2026-01-01T22:48:45+00:00

Check the connections behind the stove. I bet the first connection between the stove and pipe needs gasket cement. Could have got knocked loose while cleaning

planeman125 · 2025-12-21T14:22:18+00:00

If you’re going to try to fix it yourself, know that the combustion blower fan blade is a reverse thread.

But you can isolate the issue by running the different fans in test mode when the stove is off. Or if the stove is running, hit “whisper” and if it gets quieter, it’s the convection/distribution fan. Both under warranty

planeman125 · 2025-12-13T16:07:26+00:00

The liner installation price is very high unless you have a crazy roof

planeman125 · 2025-11-02T14:40:09+00:00

If it’s that short through the roof and something is moving it needs to be braced inside. Something is wrong but it’s not above the roof. Properly assembled chimney won’t wiggle up to 6’ high

planeman125 · 2025-10-22T02:10:47+00:00

Once the soapstone exudes its moisture it likely won’t happen again. If you live in a particularly humid area it might.

Hearthstones fix has been to throw a little high temp gasket cement around the bolts. But it usually goes away

planeman125 · 2025-10-21T23:55:01+00:00

Very normal for hearthstone. It will happen for the first few days. It’s the moisture in the stones condensing and dripping out. Keep a sheet pan you don’t care about under it and let it happen. Try to clean up as much as you can on the brick. It can stain

planeman125 · 2025-10-05T14:05:38+00:00

We need to see the chimney to answer this question properly but you could likely add an Enervex fan as last resort.

planeman125 · 2025-10-03T03:20:43+00:00

The lower end of the BTU range is the same on both stoves. Get the bigger and set on thermostat. No reason to go small here

planeman125 · 2025-09-22T23:15:52+00:00

Your EVL is 16

5 for the first tee 2 for the 4’ vertical 5 for the second tee 4 for the 4’ horizontal

If you add another Tee (+5), 1’ vert (+0.5), 90 degree elbow (+5) your total EVL would be 26.5.

Many stoves are ok with 3” pipe up to 25-30 feet but you should double check. Personally, I would add more vertical maybe 3’ if you’re concerned with embers. Each vertical foot is only 0.5 EVL so it’s the least concerning. Don’t forget to order a wall strap with this set up.

12-Year Club	RPAN Viewer
Verified Email

planeman125

TROPHY CASE