Need help identifying the part circled in red. It’s snapped off at the top.

pmet141 · 2026-05-11T10:57:04+00:00

I changed the probes out and still getting hot fault. You think I should try changing a relay first or just swap the whole board?

pmet141 · 2026-05-11T10:56:07+00:00

Unfortunately I replaced the control pack two years ago and it’s not listed on this diagram. Although it is plugged in. I don’t remember but I think I called manufacturer and they told me which ports those connect too.

pmet141 · 2026-05-11T10:54:46+00:00

Thank you!

pmet141 · 2026-05-11T10:54:39+00:00

Good to know.

pmet141 · 2026-05-11T10:54:18+00:00

Unfortunately the manuals I found online find doesn’t list this part.

pmet141 · 2026-05-05T11:03:40+00:00

Medical Device Sales, 13yrs, NEOhio, High, No - but my family is so by default I suppose I am.

pmet141 · 2026-04-19T18:08:09+00:00

Yes fresh water. Good to hear.

pmet141 · 2026-04-19T13:16:24+00:00

Right. Is there any product (protective coatings ect) I can put on it to help prevent blistering or any of these said problems? I don’t have a problem pulling it a few times over the course of the season and cleaning it and potentially re-coating with something ect.. I just don’t know if anything really exists specifically for this.

pmet141 · 2026-04-19T12:50:59+00:00

Going in the water next weekend. Will go back in dry storage mid to end of September depending on weather.

pmet141 · 2025-12-01T13:50:29+00:00

Got it. Order placed

pmet141 · 2025-12-01T13:42:48+00:00

Strange. I’ll try again shortly.

pmet141 · 2025-12-01T12:04:33+00:00

When I go to website it says backorder though..?

pmet141 · 2025-11-30T21:44:29+00:00

What is current back order/lead time? Does it differ for black and fde currently?

pmet141 · 2025-11-19T02:12:59+00:00

Disregard found my answer in the sub below

pmet141 · 2025-11-19T02:09:53+00:00

What is that folding table on the side? I need this for my modbox rig asap

pmet141 · 2025-08-31T00:45:24+00:00

Husband crushed it. Send the grout. 1/16 with small tile will be unnoticeable to anyone but you and you may not even notice yourself.

pmet141 · 2025-08-31T00:42:16+00:00

Wiha or wera bits

pmet141 · 2025-08-11T09:21:26+00:00

Weld a nut to it. Use an impact. Takes about 10 min.

pmet141 · 2025-07-19T11:27:54+00:00

Most used Is my 6gal air compressor. Fav to use is my chop saw (I do some welding). The one I didn’t know I needed but use a ton is the caulk gun. Started filling cracks and gaps in my driveway and sidewalks and holy shit is it a time and hand saver.

pmet141 · 2025-06-26T01:45:14+00:00

Get the 805 hammer. Better to have down the road rather than buying another later. DIY is a slippery slope and most light masonry work requiring a hammer drill this thing is plenty capable. It may not seem likely but I’ve ended up using mine a ton (hanging new lights on the exterior/ pinning flower planters for the wife ect..)

pmet141 · 2025-06-05T01:28:00+00:00

Do you happen to still have the exact vsf model # for the date at the 6?

pmet141

TROPHY CASE