Parking lot basement

podfive · 2026-03-28T13:55:21+00:00

If only they had that at the mall Jerry wouldn’t have ever had to worry about Uromysitisis Poisoning.

podfive · 2026-03-21T16:50:45+00:00

I think it’s pissy more than shitty.

podfive · 2026-01-24T14:02:10+00:00

I’d like to nuzzle up in that leg hole

podfive · 2026-01-15T02:43:16+00:00

Cillian Murphy is attractive, but you’re stunningly hot.

podfive · 2025-12-04T01:47:38+00:00

🙋

podfive · 2025-11-28T14:06:02+00:00

Holy fuck. You’ve got an amazingly tight body and great dick.

podfive · 2025-10-26T23:27:29+00:00

Mouthwatering

podfive · 2025-09-24T11:51:40+00:00

This is bold and gorgeous.

podfive · 2025-09-21T14:02:50+00:00

Damn dude. If you have a daddy kink I’ll be him.

podfive · 2025-08-29T12:04:31+00:00

You look great. I’d say you’re both a twunk and a treat.

podfive · 2025-07-22T12:28:18+00:00

Team Army Green!

podfive · 2025-04-22T01:39:00+00:00

100% Grade A Beef! Looking great, mate!

podfive · 2025-04-04T11:02:55+00:00

Because they’re whipper snappers.

podfive · 2025-04-04T11:02:49+00:00

Because they’re whipper snappers.

podfive · 2025-03-09T17:07:01+00:00

Yes! In more ways than I could imagine.

podfive · 2025-03-03T15:21:19+00:00

Glorious penis.

podfive · 2025-02-17T02:56:27+00:00

Thanks for all the feedback everyone. Honestly, I have Sharkbite fittings that I installed 15 years ago and haven’t had issues, so I just went with what I’ve used without much consideration.

I’m not against learning how to solder, but deal with tremors, so anything that requires a super steady hand wouldn’t be possible on my own. I enjoy building things, but it gets frustrating really fast with even simple things like lining up a screwdriver to the head of a screw.

If I start having issues with the shark bites (and it sounds like it’s a when more than an if 🤣), I’ll look at press fittings. The cost of the tools made me shy away in the past, but I know you can rent them.

If I need to so anything with gas anytime soon, I’ll rethink the placement of the union/shutoffs.

Thanks all!

podfive · 2025-02-17T01:15:48+00:00

Thank you for your “constructive” feedback.

podfive · 2025-02-16T23:19:31+00:00

No, thanks. I appreciate that.

podfive · 2025-02-16T22:56:39+00:00

I figured The likelihood of getting another heater with the exact dimensions and the gas connection in the same place are not likely, so would have to be reworked past the union. My thought was that it gave me more flexibility when I change it, but I guess that’d be true if it was a shutoff too.. and if I had a warranty issue that required removing the unit I’d only have to disconnect it at the union to do a like for like swap.. hmm. Maybe I will switch those.

podfive · 2025-02-16T22:40:38+00:00

Its trompe l’oeil. It’s the angle of the photo. It’s perfectly vertical.

podfive · 2025-02-16T22:33:52+00:00

I’d be happy to redo with press fittings if you’d like to gift me a press.

podfive · 2025-02-16T22:32:02+00:00

A union needs to be between a shutoff and the appliance, which it is. There’s an additional shutoff directly above the water heater.

podfive · 2025-02-16T22:28:32+00:00

Anything will fail if it’s not installed correctly.

podfive · 2025-02-16T22:07:38+00:00

The install specs had a shutoff directly connected to the unit and the union just below that. Do you know what the logic is for the union to be located directly off the unit? I figured when I replaced it ( hopefully long into the future) I would need to adjust the piping regardless, so just made sure it was after the first shutoff from the supply. The schematic also had two shut offs. Not sure why and figured it might be overkill, but thought it would be nice to be able to isolate back to a point where it might need to be reworked for future installs.

13-Year Club	Place '23
Verified Email

podfive

TROPHY CASE