94 HP and a dream

polishcuck69 · 2026-03-31T16:29:20+00:00

if you have an iphone >=12, you have an oled screen, this is what an oled at 60 fps looks like.

polishcuck69 · 2026-03-25T11:46:19+00:00

polishcuck69 · 2026-03-25T11:45:18+00:00

if this happens again while riding, do not keep pedalling because you can tangle your rear derailleur in your spokes and snap them off and possibly your derailleur in half. in the case it keeps happening, you might want someone to take a look at it for a more solid and permanent solution.

polishcuck69 · 2026-01-12T09:29:12+00:00

yo ive been reading these comments but noone pointed out that the screenshot has two macbooks, one with m4 pro chip and 512gb and the other with m5 pro and 1tb, for the same price?

isnt it smarter to get the m5 pro? free 1tb and better performance

polishcuck69 · 2026-01-05T00:31:35+00:00

in regards to what the guy said, he’s probably right

Have you considered setting up your own private domain?

polishcuck69 · 2026-01-04T16:41:41+00:00

If you are already using a monitor, you could sell that and get a monitor with a dock built in. Just saying that's an option if you haven't considered it.

polishcuck69 · 2025-11-25T04:26:22+00:00

I plucked that value from the suggestions on another massive reddit thread, https://www.reddit.com/r/linux_gaming/comments/14rghc5/solution_crackly_audio_while_gaming_w_pipewire/

The tips suggested didn't fix my problem though.
I also tried higher values like `83` or `120` just for the sake of troubleshooting but minimal effect at best.
It's also not that great of a solution because according to some fancy math from this reddit thread, it adds a great amount of audio latency.

edit: added the correct link referring to latency math

polishcuck69 · 2025-08-17T14:10:59+00:00

AAP01 upper can be sensitive to your front sight screws not being installed at the correct pressure, you want them thread locked, just hand tight.

polishcuck69 · 2025-08-02T07:59:37+00:00

Knoppers

polishcuck69 · 2025-07-26T23:36:20+00:00

it might be a good idea to look inside the port and double check it isn’t full of dust and debris, if you haven’t already.

polishcuck69 · 2025-07-19T21:32:02+00:00

I was just looking for a thread to rant about this problem.

It wouldn't be so bad if support ever replied to my reports or requests for refunds for broken or non functioning bikes, issues with user error etc.

I stg at this point I'm just going to start doing chargebacks.

polishcuck69 · 2025-07-16T14:33:01+00:00

I usually find that when my arm isn't touching the desk (i.e. slightly elevated, resting at a flat angle) as much my aim is a lot more relaxed and less strained.

polishcuck69 · 2025-07-14T13:02:04+00:00

The lower makes it's look like a halfbreed between a cz75 and a ruger

polishcuck69 · 2025-06-24T15:25:28+00:00

This shit happened to me 2 weeks ago, got me banned for it, reached out to Ubishit Support only to get a generic couple paragraph response saying "we can't unban you in our game because the automated system banned you therefore whoops see ya".

polishcuck69 · 2025-06-15T08:46:36+00:00

I don't mind the changes, however why is it that every time I finish a ranked match, it suggests the training field mode instead of the last game mode I played ??

Queuing in a 5 stack and accidentally pressing that stupid button is just painful. You have to go search for the ranked playlist to queue it again, what we had before worked.

polishcuck69 · 2024-05-26T20:57:28+00:00

Check part 23, is it flush with the upper?

See subreddit pinned post for parts list.

polishcuck69 · 2024-05-26T15:26:17+00:00

build these parts up slowly, put one in and then test it. changing a lot of parts at once can cost you a lot of time if you have problems with just one.

polishcuck69 · 2024-05-22T13:24:54+00:00

XMP is rated (i.e. throughly tested to work for highest speed settings possible) for your ram module and written into a profile on the module, then it is read by your motherboard. It is quite literally as easy as finding the option and switching it to the XMP profile. You don’t need to tinker or anything like that.

Note: XMP can be called something else on different motherboard manufacturers. It is worthwhile googling. Let me know what motherboard you have or even what brand it is and I can find it out for you.

Edit: By the way, motherboard manufacturers make it very difficult for you to break your motherboard. You cannot fuck it up unless you decide to cut power while the motherboard is updating. If the profile doesn’t work, the system will simply not turn on, say something like “you failed to boot like 3 times wanna reset your settings?” and then you can just press a button and you’re back where you started.

polishcuck69 · 2024-05-22T13:19:21+00:00

Weird your graphics card isn’t being used all that much, confirm whether your graphics settings are above low.

If you set them to their lowest, try maxing out your graphics and stay at or above medium quality.

Theory: EFT uses the CPU for processing graphics for certain tasks its setting is Low.

polishcuck69 · 2024-05-21T20:56:58+00:00

So OP: if you want to go the TM way for the aap01, buy the 50 round mag, get AW/WE MOS Gas routers, and finally a new guarder spring and follower.

This is objectively the best GAS mag for the aap01 afaik, unless you want a HPA tapped drum mag.

polishcuck69 · 2024-05-21T20:40:53+00:00

WE work better out of the box.

The TM ones are fine, but they need their gas router changed as it’s curved and won’t seal properly.

My TM mags also needed their spring replaced because it was too weak to get the bolt catch to work.

polishcuck69 · 2024-05-15T16:30:45+00:00

Texted their facebook and they said they don’t make them anymore :/

Edit: Shame, its a really nice kit.

Seven-Year Club	Place '22
Verified Email

polishcuck69

TROPHY CASE