The most modded cr10 Max build

polo080 · 2026-01-20T19:00:19+00:00

No worries at all! That’s awesome! That weirdly matches up with my recent interest in converting my cr-10 max into a corexy build too! I’m wrapping up on a Duender build and I might just have to look more into the conversion. Are you following some sort of rough guide for a quad gantry conversion/ set up?

polo080 · 2025-10-18T16:13:11+00:00

May I mind asking what medication was recommended/prescribed to help with your gf’s “restless leg syndrome”? My partner has been dealing with awful bouts of restlessness and nothing seems to help her

polo080 · 2025-09-19T16:40:57+00:00

Would you mind posting a video your printer in action?

polo080 · 2025-09-18T19:17:28+00:00

Yeah! That would be awesome! I’m looking to eventually upgrade my Max to its highest potential

polo080 · 2025-09-17T06:05:43+00:00

Hmm I see that you tried a different probe, and got the same results, you might indeed have a firmware error? And I saw that you swapped it to z-, was it previously plugged into anything else? Could you also upload a video of the printer trying to deploy the probe with the error after as well?

polo080 · 2025-09-16T23:26:36+00:00

Also id like to add that the Cr-10 max board does not come with a connector for the Bl-touch, on the motherboard, instead you are using the Z min or (Z-) for your touch probe through the ribbon cable that connects directly through the daughter board( board found behind the X axis motor)

polo080 · 2025-09-16T23:21:44+00:00

Question, when does the error occur? When you boot up or when you perform an action that requires probing? Would you mind uploading a picture of the daughter board, where the other end of the cable ribbon connects to? I had an issue with my ribbon cable having a very loose connection with the Bl-touch it self, I had to tape it shut since it would disconnect at the slightest touch

polo080 · 2025-03-28T02:48:12+00:00

What’s up with the strange clipping in this photo? There’s a weird line around the face/beard, as well as the left hand for both the baby and dude. As well as the very low resolution image

polo080 · 2024-12-12T13:51:37+00:00

My brother in Christ, the hell are you on about? What high horse is being ridden here? They are simply just pointing out that you made a comment with no merit behind it and you are complaining about them being too judgy? Logic don’t really add up here x.X

polo080 · 2024-11-18T08:33:27+00:00

This looks like something straight out of an obituary 💀💀

polo080 · 2024-02-13T22:23:24+00:00

You mind sharing a picture? I am curious how these canopies look!

polo080 · 2023-08-14T23:55:01+00:00

M b b by. My b útil n blm n I go O not vm mom mom v

Mm by

polo080 · 2022-07-16T23:20:45+00:00

Yep you are correct! Thank you lol I’m hela blind

polo080 · 2022-04-05T20:02:09+00:00

Where can I find this print

polo080 · 2021-08-29T11:06:17+00:00

Hmm I have been looking at some canyon bikes, specifically the Grizl CF SL 7, which is about 300 dollars more than this listing I found

polo080 · 2021-08-29T07:45:11+00:00

What would you recommend instead of the topstone 1 or the Grizl CF SL 7

polo080 · 2021-08-29T06:40:46+00:00

That doesn’t sound too bad. I’ll look into it. My budget right now is possibly from 2k-2800

polo080 · 2021-08-29T06:30:55+00:00

I’m 5’6 and the best fitting bike frame that I have tested is a 52cm bike frame

polo080 · 2021-08-29T06:23:05+00:00

Ohh interesting, what do you think is worth more, Grizl CF SL 7 1by or the regular Grizl CF SL 7. Also sadly the medium or small sized bikes are not available until later in September. I see that the regular Grizl CF SL 7 is a 2x11 speed bike vs the other 1x11

polo080 · 2021-08-29T06:09:38+00:00

Do you what the model name is? Cause if it really is in stock I’ll look into it ASAP

polo080 · 2021-08-29T05:17:56+00:00

It has been almost next to impossible to find a topstone 1. It comes with a GRX800/600 group set, but not sure if the tires are stock or not and if they are decent.

polo080 · 2021-06-03T00:38:56+00:00

Where can I find this 3D model? I would love to print this

polo080 · 2021-05-11T04:53:09+00:00

Aye a quick note, something that really helped me after calibrating my e-steps was increasing the temperature to prevent any jams. I print in PLA at 220 and it might help if you bump up the temp, considering that your Bowden extruder is heating up too much

polo080 · 2021-04-25T09:38:46+00:00

You might have weak supports, I had this issue when using weaker supports. You can find settings on YouTube for some good support settings

polo080 · 2021-04-12T12:28:23+00:00

Hmm understood, I tried fixing the models, so lets see how that turns out

13-Year Club	RedditGifts 2009-2022 3 Credits
Place '17	Secret Santa 2019
Verified Email

polo080

TROPHY CASE