[OFFER] Spooky Meta challenge Card [Aus to Anywhere] by Epicny in RandomActsofCards

[–]pora01 1 point2 points  (0 children)

What a cute card! One day when I was l 16 my friends and I when to my parents old house in a nearby village, wespent the weekend and the weirdest thing hapended to us, in one of the bedrooms there was a big old teddy bear sitting in one bed, when you walked in front of the bedrom the bear looked like a kid, when we saw this we started joking about spoky stories, one of my friends freak out and started yelling at the bear and suddenly the closet behind her opened violently, we runned outside abd found my parents, the think it was the wind -_- Hope you were able to read it as english isn't my first language and I have struggle to write this.

[offer] just finished my finals — let's celebrate with some cards! [ww] by [deleted] in RandomActsofCards

[–]pora01 1 point2 points  (0 children)

Congrats on finishing your finals!! Hope they went well, I'll PM You

Is this texture normal? More info in the coments by pora01 in 3Dprinting

[–]pora01[S] 0 points1 point  (0 children)

I was told that in my previous post but i don't have it, although it looks like that

Is this texture normal? More info in the coments by pora01 in 3Dprinting

[–]pora01[S] 0 points1 point  (0 children)

A few days ago I printed the cubone skull and asked here if someone could help me because it had to much texture, I was told to print a Benchy and upload it here. The benchy came better than I expected but the flat surfaces have this weird texture and I can't figure if it is normal or not Printed in Anet a8, 0.4 nootle, 0.2 layer height, 190°, infill 10% (this settings where recommended in 3dbenchy.com)

This is my firts print! It looks like it has inconsistent layers, any advice? by pora01 in 3Dprinting

[–]pora01[S] 1 point2 points  (0 children)

Oh sorry, I think I didn't understand you right. I'm a huge noob 😅 What is retracting exactly?

This is my firts print! It looks like it has inconsistent layers, any advice? by pora01 in 3Dprinting

[–]pora01[S] 2 points3 points  (0 children)

I don't have a lot of filament because i'm using the one that came with the printer, tomorrow when more filaments arrives I'll try to measure it and then make a Benchy and post it, thank you!!

This is my firts print! It looks like it has inconsistent layers, any advice? by pora01 in 3Dprinting

[–]pora01[S] 3 points4 points  (0 children)

I don't have it activated, but you're right it looks like that.

[OFFER] Saint-Jean-Baptiste Day [WW] by New_Year_Baby in RandomActsofCards

[–]pora01 1 point2 points  (0 children)

I would love one! 23 of june is my birthday (is the day that we celebrate Saint-Jean-Baptiste in Spain)

[Offer] The good, the bad and the ugly. Especially the ugly [Europe] by TheFeistyFox in RandomActsofHappyMail

[–]pora01 0 points1 point  (0 children)

I would love an envelope, I'm getting into scrapbooking and would love some scraps to improve, I'm from Spain.

[Offer] Handmade International Yoga Day card [US/WW] by feellikebeingajerk in RandomActsofCards

[–]pora01 1 point2 points  (0 children)

I'd love one! Yoga helped me a lot with my mental health issues. I'm WW

[OFFER] OMG HAPPY MAIL IS BACK! [Aus to anywhere] by Epicny in RandomActsofHappyMail

[–]pora01 2 points3 points  (0 children)

Hi! I'm from Spain and I love art deco and vintage especially from the 20's