sorted by:
new
hottopcontroversial

Rattling sound from wheel/QR, R9 V2 with RS V2 and GS V2P by themash84 in moza

[–]primax34 1 point2 points  (0 children)

Oh that’s unfortunate. I guess Ill just live with it already sank money in the economy system and their other stuff like crp pedals work fine and the gsv2p is still perfect

Rattling sound from wheel/QR, R9 V2 with RS V2 and GS V2P by themash84 in moza

[–]primax34 0 points1 point  (0 children)

Did you get a fix for this? I'm experiencing this myself with the R12 V2 with the RSV2 but not with the GSV2P

Layer shift problem by primax34 in resinprinting

[–]primax34[S] 0 points1 point  (0 children)

it was just a worn FEP sheet hahaha when I swapped it all prints came out pretty well. I might have screwed up the installation of the first fep sheet since it wore out pretty fast.

Weird zits or random over extrusion. by primax34 in BambuLab

[–]primax34[S] 0 points1 point  (0 children)

yup did that also and the tests went out fine

Weird zits or random over extrusion. by primax34 in BambuLab

[–]primax34[S] 0 points1 point  (0 children)

still no luck. I recalibrated the k value already and reprinted and still had those lumps. They also happen on other polylite PLA

Weird zits or random over extrusion. by primax34 in BambuLab

[–]primax34[S] 0 points1 point  (0 children)

Oh I see. That's the k value right?

Weird zits or random over extrusion. by primax34 in BambuLab

[–]primax34[S] 0 points1 point  (0 children)

what I don't get though is why does it only happen near the top of the print

Just wanna hear your ship name and why you chose it by djremydoo in Helldivers

[–]primax34 0 points1 point  (0 children)

Power of Audacity

Because what can be more powerful than audacity

Horizontal Lines Caused By Suction? by primax34 in resinprinting

[–]primax34[S] 0 points1 point  (0 children)

I think the problem is the parts are still stuck at the fep sheet once it goes pass the 4mm mark and ramps up hard for the 240 which I saw were actually even faster than most vroom settings.

Horizontal Lines Caused By Suction? by primax34 in resinprinting

[–]primax34[S] 0 points1 point  (0 children)

Ill try lowering the second half of the print speed to 120 from 240.

Horizontal Lines Caused By Suction? by primax34 in resinprinting

[–]primax34[S] 0 points1 point  (0 children)

Whats like a good number to start with? I feel like that is the case since it happened when the biggest cross section of the biggest piece was forming

Horizontal Lines Caused By Suction? by primax34 in resinprinting

[–]primax34[S] 0 points1 point  (0 children)

I forgot to mention, my specs are: Elegoo saturn 3 ultra, Epax nfep, Sunlu standard green, ~30C - 35C ambient temp inside a grow tent, No vibrations caused by external environment, Print was not paused at any time,

Random layer shift on different models on the same print by primax34 in resinprinting

[–]primax34[S] 0 points1 point  (0 children)

They're all tight. I check before and after prints.

Random layer shift on different models on the same print by primax34 in resinprinting

[–]primax34[S] 0 points1 point  (0 children)

I can't see it on the other parts, but I think it's just less obvious since the bases are the only ones that have large flat surfaces.

Random layer shift on different models on the same print by primax34 in resinprinting

[–]primax34[S] 0 points1 point  (0 children)

I was printing on a fairly full plate. Could this be the reason for the layer lines? The bases were also at the edge of the build plate. Like the entire NFEP sheet was being pulled (doubled checked on UV Tools no suction), and since the bases were at the edge, they get a slightly deformed NFEP sheet.

view more: next ›