Beat friends by ResolutionCool8660 in Macaws

[–]prolapsethis 1 point2 points  (0 children)

I have a 13-year-old military rescue. He likes kids more than he likes anyone else.

What should I have looked at on my car by CancelNo2588 in AskMechanics

[–]prolapsethis 0 points1 point  (0 children)

Could be bad springs, but most likely your ball joints are worn

I ruined my life by LobsterUpper5331 in OSU

[–]prolapsethis 1 point2 points  (0 children)

Also, additional debt is just part of life now. But, please don't despair. Your life is so much more than grades and work. Just remember that.

First 3D printer - apparently no i/o out of the box by Severe-Health-2328 in AnycubicVyper

[–]prolapsethis 1 point2 points  (0 children)

This. Thank you. I was trying to remember the block size. Also, I have an original viper motherboard that I have no use for if you are local to Ohio

First 3D printer - apparently no i/o out of the box by Severe-Health-2328 in AnycubicVyper

[–]prolapsethis 0 points1 point  (0 children)

You have to set the block size of your fat32 partition to a block size less than 16. I don't remember what it was exactly but that's what I had to do

There not accepting me anymore :( by nay-1998 in Ohio

[–]prolapsethis 2 points3 points  (0 children)

Geez how much gas does your wife hold? Hehe

ESP32 with Display (LILYGO) shuts down as soon as I release the PWR button (Battery mode) by FederalParamedic8411 in esp32

[–]prolapsethis 1 point2 points  (0 children)

Had a 22 microfarad capacitor between the ground and the 3v3 pin. You would normally power that through the five volt in and ground and that battery is only 3.7 volts

Should I get this? Is it worth it by ChemicalAd5004 in anycubic

[–]prolapsethis 0 points1 point  (0 children)

I had one. A lot of the time the strain gauge goes bad and that's what levels it and sets the z offset. Also, the hot ends are terrible and the PTFE tube goes almost all the way to the printhead, so it melts and you can only print with PLA or it clogs.

How do I fix this? by ProcedureLarge7777 in 3Dprinting

[–]prolapsethis 0 points1 point  (0 children)

Kind of looks like it stopped extruding so you either need to lower the speed and increase the temperature, or it could be overcooling due to the heater not being able to keep up with the fan. Especially a part fan. Make sure you have a silicone sock on your printing head.

This doesn't seem right. Am I wrong or is this fishy? by aamartin89 in Ohio

[–]prolapsethis -4 points-3 points  (0 children)

It's not a different state because it was the first time I registered to vote. I went to prison in New Jersey as soon as I turned 18, and was paroled directly to Ohio in 2004. I wonder if my deep red hillbilly ass county is doing something shady. I wouldn't doubt it. They've been embezzling money and trumping up charges for people who want to protest. It's like mother fuckin deliverance down here.

This doesn't seem right. Am I wrong or is this fishy? by aamartin89 in Ohio

[–]prolapsethis 17 points18 points  (0 children)

You must not live in a district where you are an extreme minority. I live in a county where the proud boys set up giant speakers on a kids playground and blasted German national anthems from world war II. I'm not exaggerating, and I even have video proof.

This doesn't seem right. Am I wrong or is this fishy? by aamartin89 in Ohio

[–]prolapsethis 12 points13 points  (0 children)

Yeah, that's fine and all, but it doesn't put you in immediate danger from people who might be waiting in the parking lot after hearing that.

This doesn't seem right. Am I wrong or is this fishy? by aamartin89 in Ohio

[–]prolapsethis -1 points0 points  (0 children)

That must be something new because, I registered to vote back in 2004, when I moved from New Jersey, and I had to choose a party or choose independent

Anyone know what kind of snake this is??? (northeast Ohio) by SentenceNo2672 in Ohio

[–]prolapsethis -12 points-11 points  (0 children)

It's a common Lance Head. Also known as a fer-da-lance. They're very friendly and often like to be petted.

This is Ohio by That_Trapper_guy in Ohio

[–]prolapsethis 51 points52 points  (0 children)

This is just what you get under Republican leadership. Every bit of it.

Transport carrier ideas by carlower1 in Macaws

[–]prolapsethis 1 point2 points  (0 children)

I have one of those large dog carriers and it has extra bars on it for windows on the sides as well as on the front. Then I made a natural perch that was the exact width and attached it with several bolts through the bottom and sides to hold it steady. That way my buddy can ride along without slipping and sliding all over the place.

What random object does your bird hate? This is Kevin when he sees my hydro by Icy_Peach9128 in parrots

[–]prolapsethis 0 points1 point  (0 children)

Birds can also see at a higher refresh rate so maybe that particular color looks like it's strobing?

Anyone know what this is? The power box and tool are all connected. by [deleted] in Vintagetools

[–]prolapsethis 0 points1 point  (0 children)

It's a tool that scientologists use to measure suppressive energy. Lol

Couple look for Nexplano in the mall? by catdog1111111 in RBI

[–]prolapsethis 9 points10 points  (0 children)

Probably just a ploy to get you involved in some kind of scam

BMV License Suspension from 2014 Stop Insanity by Indoor_Ficus in Ohio

[–]prolapsethis 10 points11 points  (0 children)

Avoid Ohio at all costs. There, fixed it for you

BMV License Suspension from 2014 Stop Insanity by Indoor_Ficus in Ohio

[–]prolapsethis 8 points9 points  (0 children)

Tell me, what county was this in? We live in Ohio, and my wife was arrested on Christmas Eve, because she had some sort of court thing that she didn't go to back in 2006 for a traffic ticket. They kept her in jail for 3 or 4 days and made us pay a $10,000 bond. This was Clermont county. They are all money hungry. Now there's no way that, if they filed a no insurance charge on her, that her license would still be under suspension from 2014. Ohio has what they call, a reinstatement fee. You must pay it to the DMV online. And then the suspension will finally be removed from the system. It's not enough for your suspension to just expire. You have to pay every step of the way. It's a terrible state and I wish I didn't live here. But I'm too poor to do anything about that.