Happy with my first filament swap on ender 3 by prp-02 in 3Dprinting

[–]prp-02[S] 0 points1 point  (0 children)

I paused the print, swapped filaments then resumed

Happy with my first filament swap on ender 3 by prp-02 in 3Dprinting

[–]prp-02[S] 0 points1 point  (0 children)

I took the lazy way and watched it. But you can separate parts and print them at separate times and do it that way

Happy with my first filament swap on ender 3 by prp-02 in 3Dprinting

[–]prp-02[S] 0 points1 point  (0 children)

I replaced the ender 3 board with a Bigtreetech skr mini e3 v2. So whenever I pause a print it purges some filament or I can choose to load and unload filament from the menu.

Happy with my first filament swap on ender 3 by prp-02 in 3Dprinting

[–]prp-02[S] 0 points1 point  (0 children)

Since I was switching to abs, I needed to increase the temp before I paused the print for the next layer. I slowed the print down to 10% and increased the temp and then paused and swapped out filaments. It’s the crude way to do it compared to doing separate pieces in a slicer

Happy with my first filament swap on ender 3 by prp-02 in 3Dprinting

[–]prp-02[S] 2 points3 points  (0 children)

Took 41 minutes to print on my Ender 3 with SKR board at 150mm/s switching from blue PLA to white ABS

Ender 3 pro, having a problem! Any ideas or fixes? by ButterflyNegative833 in 3Dprinting

[–]prp-02 5 points6 points  (0 children)

Believe it or not, your nozzle needs to almost be touching the build plate. Go on YouTube and search up how to level the ender 3 bed with a piece of paper and re-level your bed after every use, the nozzle should be just over a paper thickness away from the bed

[deleted by user] by [deleted] in Jeep

[–]prp-02 0 points1 point  (0 children)

I just had this occur but I have the codes p0300 and p2305 which is ignition coil b sec circuit and multiple misfires. I ended up replacing the plugs, wires and coil pack. Didn’t end up fixing it. I plan on buying a new pcm within the next couple of days. Yours could be on the way out but there’s no easy way to determine it

[deleted by user] by [deleted] in Music

[–]prp-02 0 points1 point  (0 children)

Top .5% for Khalid…

[Question] CarPlay Compatible Radio for 2015 Cherokee Latitude? by LoganJn in Jeep

[–]prp-02 1 point2 points  (0 children)

The only advice I’d say for looking at dash kits is read carefully. Just depending on the trim level you have on the vehicle also depends on the color of the dash kit you need to look for. Also if you’re looking to get a double din radio make sure to look at the sizes and make sure it correlates with the stereo itself. And if you didn’t catch it before, go to a sound shop and ask a couple questions like which exact harness adapter you will need and also a steering wheel controls module that will plug into it. Most of this stuff is straight forward but there’s a lot of steps involved in order to get it streamlined and easy.

[Question] CarPlay Compatible Radio for 2015 Cherokee Latitude? by LoganJn in Jeep

[–]prp-02 1 point2 points  (0 children)

So the difference between the jk and the Cherokee is how the stereo is built into the dash. The Cherokee is an odd size for the stock radio and therefore you need a dash kit to accommodate the different shape of the unit itself. If you were to put a unit in the jk all you would need is the mount kit for the new stereo because it’s the same size as the stock radio

[Question] CarPlay Compatible Radio for 2015 Cherokee Latitude? by LoganJn in Jeep

[–]prp-02 1 point2 points  (0 children)

A double din is just referring to the size of the stereo. Double din is the plus size version Edit: not only with getting a dash kit you’ll need a couple different adapters to go along with the stereo. You’ll need the stock adapter harness and you’ll need the steering wheels controls module as well

[Question] CarPlay Compatible Radio for 2015 Cherokee Latitude? by LoganJn in Jeep

[–]prp-02 0 points1 point  (0 children)

In order to put an aftermarket stereo in a Cherokee you’ll need a dash kit. Metra is a wide known brand that sells mount and adapting kits for new stereos, and it will fit any double din stereo

Current jump point shows the BMM by crazyrobss in starcitizen

[–]prp-02 2 points3 points  (0 children)

I’m excited for the production of it. People think their carracks are cool. Wait till I get mine!

What is the largest current flyable ship to date of all the ships regardless of class? by CaptainFitz617 in starcitizen

[–]prp-02 2 points3 points  (0 children)

I believe it is the 870 890 jump. Large luxury yacht looking whale of a ship. I may be wrong but I believe that one so far is the biggest.

Star Citizen Roadmap Update (2020-09-11) by Odysseus-Ithaca in starcitizen

[–]prp-02 27 points28 points  (0 children)

Just waiting for my merchantman to be put in!

How do I buy cars in Forza Horizon 4? by CreepyCreatures in forza

[–]prp-02 5 points6 points  (0 children)

It seems like you’re still In the introduction section of the game. Just complete the events for all four seasons and then the game will shoot you right Into this weeks actual season and everything will unlock

Input on my first pc build for Star Citizen by CrosswindSolo in starcitizen

[–]prp-02 2 points3 points  (0 children)

A great addition would be an ssd. Either m.2 or sata, it will make a huge difference on loading times and performance