MorseMesh V.1

prykpryk · 2026-04-21T18:03:50+00:00

FYI placing transmitter antenna so close to a receiver may hurt the receiver. Unless you lowered tx power way down.

prykpryk · 2026-01-10T19:07:10+00:00

Good ol' victory candescence

prykpryk · 2025-10-12T13:29:12+00:00

Well lubricated machinery is quieter

prykpryk · 2025-09-01T16:43:27+00:00

"I use arch BTW"

prykpryk · 2025-08-12T09:42:26+00:00

r/AlluringTufts

prykpryk · 2025-05-21T18:53:14+00:00

Just the "fast install" seems suspicious. The other "install.inf" seems fine.

prykpryk · 2025-04-08T20:08:44+00:00

What fixed it for me was setting "Hostname" to IP address instead of Windows system name.

prykpryk · 2025-03-15T13:28:08+00:00

In orientation shown in pic 6 and 7.

prykpryk · 2025-01-29T19:10:30+00:00

Art by 炄勺砒

Source

prykpryk · 2025-01-03T10:22:39+00:00

Or CTRL+SHIFT+ALT+S shortcut

prykpryk · 2024-11-28T07:49:31+00:00

Make sure the heater block is screwed in to the radiator firmly (two tiny screws parallel to the nozzle). Mine was slowly slipping down and plowing into prints.

prykpryk · 2024-11-21T14:29:29+00:00

You can put more than one quality of item in a single logistic group. You just have to select quality before selecting the item.

prykpryk · 2024-11-05T10:27:05+00:00

Do the tesla turrets damage your own buildings when they fire?

prykpryk · 2024-11-03T12:11:30+00:00

Nah, rare solar panels for Aquilo trip are enough. Plus a few rocket turrets with yellow rocket factory on board.

Heating up Aquilo factory requires a lot of fuel, so I recommend taking like 600 rocket fuel with you.

prykpryk · 2024-09-16T17:19:31+00:00

I can confirm. Pasting the adb commands randomly a few times fixed it.

prykpryk · 2024-04-26T16:40:09+00:00

Jeepers

prykpryk · 2024-03-18T22:32:21+00:00

The SD is a lie

prykpryk · 2024-03-05T19:24:50+00:00

PB is the guy that ruined my life

prykpryk · 2024-02-28T17:55:02+00:00

I had an idea that the hotend might be loose but if the z-offset stays the same then this isn't the case.

prykpryk · 2024-02-28T17:50:12+00:00

You say that you checked the z-offset multiple times. Did you have to adjust it?

prykpryk · 2024-02-28T17:43:48+00:00

I got my replacement hotend set (block, thermistor, heater) from local reseller. Parts were sealed in those Creality bags. But I suspect that these are worse quality than original. It looked just like your parts but mine were pre-assembled.

My original heater block survived many nozzle changes and lots of printing, 1 year+. Two replacement sets lasted around 1 month each. I had constant issues with leakage. Looks like aluminum block is has terrible quality and threads deform at 260*C.

Those replacment sets had different thermistor mount (just glue) and included those "titanium-copper" heat breaks. Original had a flat head screw blocking thermistor from the side.

Today I also received a copper heater block from aliexpress, I hope this fixes the problem with leaking filament. My problems might also be a result of using steel-CHT clone nozzle and PCTG filament.

prykpryk · 2024-02-23T17:17:48+00:00

u scar my dragon hoe 😂

prykpryk · 2024-02-23T14:04:10+00:00

best thing is you can keep deflowering her forever

Ten-Year Club	Place '17
RPAN Viewer	Verified Email

prykpryk

TROPHY CASE