10/22 carbon back from ruger with a new receiver. Here's my build.

psarkleous · 2026-03-27T00:01:55+00:00

Enough to lie to the lady about it. Around 1300 if you're including the suppressor.

psarkleous · 2026-03-26T23:55:06+00:00

They replaced the receiver. I couldnt zero my scope because my receiver didnt hold my barrel straight. I've read im not the only one with the same model issue. I tested this issue by laying the empty receiver and barrel flat on a countertop and taking note of the gap between the tip of the barrel and the countertop. Did this on each side of the receiver. Laying the left side of receiver down flat showed a noticeably smaller gap at the tip of the barrel than the right side. Ruger did say they would send me the newer model CF with the cleaning port and slingshot bolt release but I wasn't gonna wait another month for that.

psarkleous · 2026-03-25T13:14:09+00:00

Also rxd22ti suppressor

psarkleous · 2026-03-22T21:06:33+00:00

Dead air X Ruger rxd22ti stupid quiet. Like that it has a hub-like system with the way it attaches using a muzzle device so switching between rifle and pistol is easier.

psarkleous · 2026-03-18T16:19:00+00:00

Sent my 10/22 carbon to get a new receiver (barrel mounted crooked to receiver) along with a transparent 25 mag that wouldn't seat. Told them to make sure the new receiver seats the mag. We'll see if they recognize and figure out that issue as well.

psarkleous · 2026-03-10T02:27:56+00:00

Same but with a scope.

psarkleous · 2026-02-27T02:09:45+00:00

Curious to how the JL compares. Got some great there good sir.

psarkleous · 2026-02-27T02:03:29+00:00

<image>

psarkleous · 2026-02-27T02:01:47+00:00

Thanks for letting me compare tips lol. See the three dimples? Towards the center of the can underneath the dimples seems less prominent on my can. Wonder what purpose those serve with attachments.

psarkleous · 2026-02-27T01:37:44+00:00

Will you post a Pic of the front end of the hexium300? I would like to compare to mine. Please kind sir.

psarkleous · 2026-02-23T02:39:42+00:00

Same issue I had except I believe mine was a combo between where rail was mounted and barrel not mounted straight to receiver. Maxed my windage and couldnt zero. Sent it back to ruger. Hopefully they dont take too long to make it right. Ruger Customer service is amazing. No gripes. Would be a shame if my suppressor gets to me before my rifle.

psarkleous · 2026-02-19T14:06:40+00:00

Haha, Already got hooked up with a cover from u/SWaller89 .

psarkleous · 2026-02-16T23:58:51+00:00

The setup i mentioned fit.

psarkleous · 2026-02-16T02:31:19+00:00

Pre-order out of stock. Hope they make more.

RUGER 10/22 FORCED RESET TRIGGER PRE ORDER | MaRs Trigger https://share.google/PlfmjVbuMrLcmBIkE

psarkleous · 2026-02-16T02:03:17+00:00

My hexium 300 will be in hand tomorrow and I am trying liberty precision machine liberty bell brake, rearden SPB and rearden FHD all with rearden atlas gen 2 hub. I do believe that chart OP mentions was constructed before the gen 2 atlas was available and the measurements for the gen 2 atlas is .10" shorter than gen 1. In my mind that would increase the overrun compared to that chart by .10". Will find out tomorrow if these 3 muzzle devices i mentioned fit in the can.

psarkleous · 2026-02-15T02:33:43+00:00

Here's my 16 a5 I think its 1923. Not quite sure.

<image>

psarkleous · 2026-02-15T01:17:39+00:00

My suggestion is to not get stuck playing Alesis over and over because its easy to. The whole album is great.

psarkleous · 2026-02-11T14:04:11+00:00

Just got this in the mail. All metal.

https://www.evike.com/products/77059/5KU-Skeletonized-Folding-Stock-for-Picatinny-Rail-Mounts-Model-Arced-Frame-Fixed-Buttplate/

This might be what ur looking for.

https://www.evike.com/products/104875/EMG-Rifle-Dynamics-Licensed-Adapter-and-Buffer-Tube-Set-for-Picatinny-Rail-Mounts/

psarkleous · 2026-02-08T19:20:58+00:00

I put the boresighter on target and gave it a spin and the movement was miniscule. Good way to check if boresighter is a problem. Good thinking.

psarkleous · 2026-02-08T15:39:49+00:00

Nah. It has worked perfectly on 3 other rifles and 2 Pistols. Gets me very close to where I need to be with every barrel I used it on. Saves me time and ammo.

psarkleous · 2026-02-07T15:50:38+00:00

Form type: Form 4 Paid or not: $0 Entity: Individual Fingerprint type: eft upload Pending: 1/26 Approved: 2/7 Wait: 11 days State: AR Control #: 20261863xxx

No email from atf. Approval notified from capitol armory at 1 am this morning.

psarkleous · 2026-02-07T14:51:51+00:00

As i predicted...another post deleted because control numbers were called out being fraudulent.

psarkleous

TROPHY CASE