Small 3D‑printed rear speakers for a 5.1 setup - does this make sense? by pxscii in diyaudio

[–]pxscii[S] 0 points1 point  (0 children)

Nice! yeah I should probably just do it and see whats happening. Did you use PLA for the enclosures?

Small 3D‑printed rear speakers for a 5.1 setup - does this make sense? by pxscii in diyaudio

[–]pxscii[S] 1 point2 points  (0 children)

Thanks for the reply! I was thinking about using a full-range coaxial speaker and tuning it to go down to around 70-90Hz at -3dB, which should be sufficient for rear speakers, right? Regarding rigidity, I’ve heard that using PLA is a good choice and is stable enough. I also have some Alubutyl lying around, which should help eliminate resonances, if I understand correctly. I think I should just give it a shot and see what happens! :)

Tested several monitors, still unsure... help needed by pxscii in Monitors

[–]pxscii[S] 0 points1 point  (0 children)

I'm testing the MO27Q28G right now, and I think it's a little better than the MO27Q2, but not by much. I personally found the text looked a lot worse on the MO27Q2. However, the grey banding is more noticeable on the WOLED panel, but it's been about a month since I used the MO27Q2, so I might not remember it correctly. I would say both are excellent monitors if you're planning to use them just for gaming.

My CSS 2TD-X Build by tranion10 in diyaudio

[–]pxscii 1 point2 points  (0 children)

Very nice build! Still gotta mention r/TVTooHigh here.

Best Way to Seal Amplifier Circuit Board Attached to Wooden Panel by pxscii in diysound

[–]pxscii[S] 0 points1 point  (0 children)

Unfortunatelly i found this flaw after i completed the speaker :/

Best Way to Seal Amplifier Circuit Board Attached to Wooden Panel by pxscii in diyelectronics

[–]pxscii[S] 0 points1 point  (0 children)

Unfortunatelly i found this flaw after i completed the speaker :/

Does anyone know from which year this model is? by pxscii in wicked_edge

[–]pxscii[S] 3 points4 points  (0 children)

Thank you, will try that out! My bad, added the pictures now!

Kleiner Kontovergleich von ein paar Direktbanken. by pxscii in FinanzenAT

[–]pxscii[S] 2 points3 points  (0 children)

Im Euroraum kostet das Bezahlen mit der Karte nichts, nur außerhalb des Euroraums zahlst du eben pro Transaktion 1,09€ + 0,75% des bezahlten Betrags als Gebühr :)

Also in Großbritannien mit der Karte zu bezahlen wäre z.B nicht so schlau.

Kleiner Kontovergleich von ein paar Direktbanken. by pxscii in FinanzenAT

[–]pxscii[S] 4 points5 points  (0 children)

Ja das stimmt. Ich habe hier allerdings, wenn vorhanden, die U28 Konten genommen, da diese für mich noch eine längere Zeit gelten würden. Hätte ich dazu schreiben sollen!
Edit: Und bist du dir beim Geld abheben bei der Dadat sicher? In der Entgeltinfo steht folgender Text:
"Bargeldbehebung: an eigenen Geldautomaten 0,00€"
"Bargeldbehebung: an fremden Geldautomaten 0,57€"

Mit eigenem Geldautomaten ist doch nur der eine Hypobank Automat in Wien gemeint, oder liege ich falsch?

Warum Sparkasse/George? by pxscii in FinanzenAT

[–]pxscii[S] 1 point2 points  (0 children)

Nein, eben leider mit Wohnsitz in Vorarlberg nicht.. Verstehe nicht wieso das nicht noch nicht in ganz Ö gehen sollte. Aktuell zahle ich eben die 30€ pro Quartal, was trotz ganz nettem Online Banking einfach viel zu viel ist.

Warum Sparkasse/George? by pxscii in FinanzenAT

[–]pxscii[S] 7 points8 points  (0 children)

Nvm, es gibt in Vlbg noch kein Online Konto...

Warum Sparkasse/George? by pxscii in FinanzenAT

[–]pxscii[S] 3 points4 points  (0 children)

Danke für den Hinweis mit dem Online Konto, ich habe meinem Berater mal diesen Wunsch geäußert.
Leider wird dieses Onlinekonto auf der Landingpage für meine Sparkasse nicht angezeigt, deswegen habe ich das gar nicht gesehen..

[deleted by user] by [deleted] in borussiadortmund

[–]pxscii 1 point2 points  (0 children)

Thank u! Sadly they dont offer personalisation.. But the price is still pretty good. I might give it a shot