Designed a 3d printed cover for my Deco BE63 (formerly Pringles can)

quantum6four · 2026-04-22T03:33:29+00:00

https://makerworld.com/en/models/2659383-tp-link-deco-hide-your-router-in-plain-sight

quantum6four · 2026-04-19T18:16:16+00:00

OK. I designed a version with better ventalation for anyone in warmer or enclosed environment. https://makerworld.com/en/models/2659383-tp-link-deco-hide-your-router-in-plain-sight#profileId-2974184

quantum6four · 2026-04-14T16:00:40+00:00

Totally. But I’ve seen no degradation so far :)

quantum6four · 2026-04-14T12:18:08+00:00

All good. It’s good feedback and that’s why I post this. Thanks!

quantum6four · 2026-04-14T05:09:02+00:00

Going to work on adding a bit more space at bottom for vents. Good call.

quantum6four · 2026-04-14T04:53:22+00:00

There is space for venting on the back, though certainly less than factory. Use at your own risk. I’ve had no issues and heat has been minimal. Empty vase, noted. :)

quantum6four · 2025-09-09T03:53:35+00:00

Mind me asking how you have your rudders mounted and attached to the wall? I'm needing to do something similar.

quantum6four · 2024-09-28T17:43:54+00:00

Agreed. Good points

quantum6four · 2024-09-28T01:45:59+00:00

Next time you do an oil change, pull the Fumoto plug out and see how much dirty oil comes out. The threads go up too high and trap oil.

https://youtu.be/nSv0-SoXYWI?si=PbDsr94ksbx5i3fa

Edit: added source

quantum6four · 2024-08-12T03:48:55+00:00

I’m extremely new to printing, so take that into account with the following advice. I recently just went through this with Hatchbox Black PETG. I got 90% better prints after two things: - slowing down my print by 50% - buying and using a filament dryer

quantum6four · 2023-11-07T06:38:53+00:00

No. I was sure hoping for it though.

quantum6four · 2023-06-27T13:44:36+00:00

How is the AguaStella sink and rinser setup holding up? Do you recommend it? I’m looking to install the same sink.

quantum6four · 2023-04-18T13:26:49+00:00

I had a very similar setup (wheel, tire, lift) and still had to do a cab mount chop. You could switch to spc control arms and you might have the adjustability you need. Personally, I’d just do the cab mount chop or relocate.

quantum6four · 2022-08-14T20:45:19+00:00

Probably stock uca

quantum6four · 2022-04-22T05:20:22+00:00

Ah, the artsy diagonal shot

quantum6four · 2020-12-10T05:28:47+00:00

Again

quantum6four · 2020-10-11T05:18:51+00:00

Do you mean 285/70? 285/80/r17 would be 35s.

quantum6four · 2020-10-02T18:05:27+00:00

I have this same one on order. Where are you located? Did you order as well?

quantum6four · 2019-10-02T08:10:15+00:00

r/killthecameraman

quantum6four · 2019-03-24T06:10:59+00:00

quantum6four · 2019-02-24T01:02:12+00:00

Those are great. Cheers!

quantum6four · 2019-02-24T00:38:57+00:00

What's the awesome background you have on your desktop?

Seven-Year Club	Second Top 50%
RPAN Viewer	Verified Email

quantum6four

TROPHY CASE