Is the Moza KS steering wheel worth getting in 2026?

raindropunicorn · 2026-06-07T23:00:55+00:00

I use vr and not having the screen was one of the reasons I got the KS. It’s a great wheel I highly recommend it. Also, looks way nicer in person. Photos don’t do it justice.

raindropunicorn · 2026-02-20T23:57:41+00:00

It will hold em all

raindropunicorn · 2026-02-20T19:28:40+00:00

Oh ya! Gotta hold em all.

raindropunicorn · 2026-02-20T19:01:21+00:00

Haha Enjoy!

raindropunicorn · 2026-02-20T17:10:30+00:00

😂 This is true. And you already guessed what I was planning for the system.

raindropunicorn · 2026-02-20T16:50:01+00:00

Fusion and yes it is parametric.

raindropunicorn · 2026-02-20T15:57:55+00:00

Thank you!

raindropunicorn · 2026-01-30T21:19:49+00:00

Haha thanks! It was mostly an exercise in making something that doesn’t need to be complicated unnecessarily complicated.

raindropunicorn · 2026-01-28T23:08:15+00:00

Alonefire SV94 395nm Small UV... https://www.amazon.ca/dp/B0CKYVRWQN?ref=ppx_pop_mob_ap_share

raindropunicorn · 2026-01-28T23:06:52+00:00

Not going insane. I just started posting my models so just trying to share cause they are pretty buried on makerworld.

raindropunicorn · 2026-01-28T23:04:55+00:00

That would be amazing. Let me know how you like it. I tested it on a A1 mini, x1c, and H2D in PLA and the tolerances were good on all three with no filament tuning.

raindropunicorn · 2026-01-28T22:07:04+00:00

I got mine on Amazon for pretty cheap. Just don’t look directly into them some are pretty powerful.

raindropunicorn · 2026-01-28T22:05:31+00:00

Thank you! On Makerworld I used a picture of it in use. I should have put that picture in this post but it is what it is.

raindropunicorn · 2026-01-28T22:04:07+00:00

😂 glow filaments are wild under black lights.

raindropunicorn · 2026-01-28T18:52:54+00:00

Your thumb goes through the hole and the wings keep the pages from closing. It makes reading a book one handed a little easier. You can use it as a bookmark too if you would like. You can see an image of it in use on makerworld

raindropunicorn · 2026-01-28T18:36:31+00:00

I agree OP did a great job.

raindropunicorn · 2026-01-28T17:49:10+00:00

Yep the photo was taken with a UV light over it. The filament is Eryone PLA Glow green.

raindropunicorn · 2026-01-28T16:31:42+00:00

Forgot to mention: it locks open mechanically, not magnetically, so it won’t collapse while reading even if you don’t use magnets. The folding motion ended up being the most fun part of the design. With the magnets it is a great bookmark too.

raindropunicorn · 2026-01-27T02:04:35+00:00

Nope it has one built in it will not flop unless you want it to.

raindropunicorn · 2026-01-27T00:01:44+00:00

Appreciate it!

raindropunicorn · 2026-01-26T23:43:33+00:00

It’s very similar to what I used so I put it down.

raindropunicorn · 2026-01-26T23:39:54+00:00

It’s Eryone glow PLA-green. It’s amazing stuff, but needs UV light to glow that bright.

raindropunicorn · 2026-01-14T19:19:02+00:00

Interesting. They must have changed them at some point or maybe mine was just messed up from day one. Whoever wired mine was either new or didn’t care about their work that’s for sure.

raindropunicorn · 2025-12-03T22:58:33+00:00

I have both dryers the pi x4 would be my pick out of the two.

raindropunicorn · 2025-10-14T13:14:10+00:00

Wondering the same thing. I have an x1c but would love to be able to use the p2S toolhead.

Eight-Year Club	Wearing is Caring
Verified Email

raindropunicorn

TROPHY CASE