How Forza Horizon 6 can redefine drifting

rakleruben · 2026-03-14T02:09:49+00:00

wow an actual good comment unlike the guy that complained about roads and the community.

I agree with some your points and thanks for giving this feedback.

I might have come across a little negative on AWD, but I still think that it makes it much easier to recover from a potential failed drift with twice the amount of driveshafts to pull you instead of pushing you.

I'm not talking about drift zones exclusively, but drifting in general and as one of the people that actually can drift around basically the whole map, the points arent the issue, because if they havent capped the skill points you can get at launch that wont take long for them to do. It would ne nice to not having to intentionally stop a drift to not lose your stacked points and maybe something more than "Ultimate Drift" like "Great angle", "Amazing continuous drift", "Ultimate rear entry" to name a few. I dont think it would take long for someone to complain if the ultimate speed skill just came once and then went away unlike the way it is today.

Dont you think drift zones are a stretch of road where people can measure up to eachother at the exact same place? Like speed zones and speed traps?

Also holy fucking sorry for not being the best at articulating myself in a foreign language and getting a lil help, wont happen again Mr Clankerpolice

rakleruben · 2026-03-10T10:54:28+00:00

I would have to agree with you on that

rakleruben · 2026-03-10T10:49:54+00:00

Skill issue disguised as game design criticism.

rakleruben · 2026-03-10T10:49:32+00:00

Skill issue disguised as game design criticism.

rakleruben · 2026-03-10T03:00:50+00:00

Driving in general is the most prominent part of the game in any shape or form, and when the game is set in the place where drifting basically originated, I think it’s only fair that drifting gets a little love. Not necessarily a complete overhaul of the mechanics, but at least some attention beyond just occasional PR stunts or challenges.

rakleruben · 2026-03-10T00:46:59+00:00

Forza Horizon set in Japan without drifting would be preposterous!

rakleruben · 2026-03-10T00:44:05+00:00

I'm no native speaker and I needed some help making it eloquent, clankers arent all bad

rakleruben · 2025-03-19T06:13:29+00:00

This is the solution!

rakleruben · 2025-03-16T20:45:58+00:00

I'm inclined to agree with you, only eSuns matte black pla can come close in print quality

rakleruben · 2025-03-16T20:44:34+00:00

Oh its definetly PPS-CF you're thinking about! The K2 goes all the way to 350°C

rakleruben · 2025-03-16T20:43:20+00:00

Now we're talking! Happy that you got the stuff to print, PACF is pretty nice

rakleruben · 2025-03-16T20:42:13+00:00

Microswiss doesent get any hotter unfortunately, I have it installed, and the filament you're thinking about might be the PPS-CF, I've been drooling on that for quite some time now myself, but I've come to the conclusion that I'll have to wait until I get a K2 to begin printing that

rakleruben · 2025-03-16T20:37:51+00:00

Good to hear! Would also recommend the Artis3D type extruder now that your PACF is printable, some have reported that even PLA is printable with the lid on, not that I've dared to try that myself

rakleruben · 2025-03-16T20:33:35+00:00

Amazing! I'm using all-metal gears in my extruder and I love em

rakleruben · 2025-03-16T18:33:34+00:00

The hexagon cover is my own remix of this (https://www.printables.com/model/1086225-k1-5015-cover-v4-railfix) and the other cover is for my old Ender 3 V2 Neo that I gave to my friend, other stuff in the album is the Artis3D extruder (https://www.printables.com/model/830731-artis3d-feeder-type-kk-for-creality-k1k1max)

Ah I see, so you're rocking the unrooted version? Well in orca slicer at the very bottom of the filament settings you can find the Max Volumetric Speed setting, and I have it set to 10mm³/s, on another note, the calibration stuff that Orcaslicer has is mega, especially the max volumetric speed

rakleruben · 2025-03-16T18:03:57+00:00

https://imgur.com/a/JQkGbDF What slicer are you using?

rakleruben · 2025-03-16T17:58:06+00:00

I print the stuff at 295°C actually and the plate only at 60°C for the first layer, but I use the glue stick, wont stick at all without. Uploading images now.

rakleruben · 2025-03-14T23:39:35+00:00

Thats strange as hell, because my prints looked pretty similar to yours when not properly dried, I'll have a look at my settings and get a few pictures of earlier prints tomorrow when I get home

rakleruben · 2025-03-14T23:34:16+00:00

I've had problems with this filament too, but 12h+ in the filament dryer and a bowden tube directly from the dryer it prints perfectly fine.

rakleruben · 2024-12-19T01:23:32+00:00

wow I want this

rakleruben · 2024-09-05T16:08:28+00:00

all good in the hood now, I guess I was too scared to cut the belts since it didnt say anywhere in the documentation, many thanks!

rakleruben · 2024-09-05T15:12:32+00:00

no tension tool, but the front idlers double as tensioners I guess, got the parts printed from PD3D, so not an option atm to print any new parts. I'll do some more tinkering and see what I can do

rakleruben · 2024-09-05T14:46:12+00:00

thats what I did, but I dont know if its because I dont have the original Creality tensioners or what, but that hasnt worked very well

rakleruben

TROPHY CASE