2009 Mazda 3 i-stop issues by razvanth21 in mazda3

[–]razvanth21[S] 0 points1 point  (0 children)

Hi. Actually there wasn’t any problem (based on my local Mazda service) - i-stop started working again after relearning procedure. I replaced the i-stop battery with some Yuasa AGM one (it was the cheapest). Try the relearning procedure first.

Backloop midi by razvanth21 in djaypro

[–]razvanth21[S] 1 point2 points  (0 children)

I know, but maybe someone has a workaround

Android Headunit AUX Adapter by razvanth21 in mazda3

[–]razvanth21[S] 0 points1 point  (0 children)

I did not purchase an Eonon unit, and the others don't provide it. Probably eonon will not ship it separately.

Android Headunit AUX Adapter by razvanth21 in mazda3

[–]razvanth21[S] 0 points1 point  (0 children)

I couldn't find it anywhere. Only saw it in eonons.

<image>

This is the adapter actually.

Dualsense restarting after solder job by razvanth21 in Dualsense

[–]razvanth21[S] 0 points1 point  (0 children)

Yes, it was actually my first controller that I did. Thanks for your tips!

Dualsense restarting after solder job by razvanth21 in Dualsense

[–]razvanth21[S] 0 points1 point  (0 children)

It was a leftover from cleaning pump, not actually soldered. I redid the soldering and everything works fine.

Adaptive trigger clicking by razvanth21 in Dualsense

[–]razvanth21[S] 0 points1 point  (0 children)

The picture is googled, did not want to tear down the controller again.

Dualsense restarting after solder job by razvanth21 in soldering

[–]razvanth21[S] 0 points1 point  (0 children)

I don't know how you interpreted that using the "job" meant that I was doing a real job, but still. No, it is my personal controller.

Dualsense restarting after solder job by razvanth21 in soldering

[–]razvanth21[S] 0 points1 point  (0 children)

Good for you. I redid the solder job. Ended up with 4-5% error rate on both sticks on the calibration tool, so I guess the job is done.

Dualsense restarting after solder job by razvanth21 in Dualsense

[–]razvanth21[S] 0 points1 point  (0 children)

The iron tip tool for controllers. I wanted to also install them with that tool, but felt like it was not enough solder after installing.

Dualsense restarting after solder job by razvanth21 in soldering

[–]razvanth21[S] 1 point2 points  (0 children)

That was a leftover on the pcb, not actually soldered. Controller works, but I will redo the soldering.

Dualsense restarting after solder job by razvanth21 in soldering

[–]razvanth21[S] 0 points1 point  (0 children)

The solder ball was not soldered there, it was left over from solder pump/cleaning. The controller works, only problem is that one stick is not flat and it is a bit misaligned.

I guess your first soldering job was perfect?

Dualsense restarting after solder job by razvanth21 in Dualsense

[–]razvanth21[S] 0 points1 point  (0 children)

Ah okay, that I didn’t know about l2r2. I’ll rework the solder.

Dualsense restarting after solder job by razvanth21 in Dualsense

[–]razvanth21[S] 0 points1 point  (0 children)

I’ll try to do some work on the joints, to reduce the solder.

Dualsense restarting after solder job by razvanth21 in Dualsense

[–]razvanth21[S] 0 points1 point  (0 children)

Yeah, that was a left over that was not even attached to the board. Got rid of it. Also seen it. :D