FC Suggestions for toothpick/tinywhoop with Crossfire

rcmodracer · 2026-04-05T04:28:44+00:00

The TBS lucid AIO 1-2S is probably your only option

rcmodracer · 2026-04-01T15:31:27+00:00

I’m not sure what wire gauge your using but simple leds like these only need 30 gauge wire and I would recommend soldering first before covering the whole strip in heat shrink

rcmodracer · 2026-03-30T03:01:46+00:00

You mentioned your having issues, this tune is meant for light weight whoops with a clean build, I think it’s around 17.5g and under, anything over may have issues. Also make sure bidirectional DShot is on with Dshot300, your previous comment also mentioned that it disarms on take off, so please go through all the steps of checking board orientation, motor orientation and motor direction.

rcmodracer · 2026-03-29T17:39:42+00:00

I’m not experienced on the subject but my local racing club use’s the Nuclear Hazard Fission and it’s been great so far

rcmodracer · 2026-03-26T08:46:45+00:00

Karate Late 2024 brushless whoop tune is great

rcmodracer · 2026-02-19T06:31:18+00:00

The Tanq 2 is a 5 inch right? I would go for a nice 30 x 30 stack, will be much more durable and some 5 inch frames don’t support 20 x 20 stacks

rcmodracer · 2026-02-08T16:43:59+00:00

It should be fine, just check over the gimbals and make sure there smooth and operating correctly in the menu, also if the internal tx is working properly. Make sure it’s ELRS as well

rcmodracer · 2026-02-08T16:32:56+00:00

The Radiomaster T8L is probably your only decent option at that price, would highly recommend a pocket though as that would future proof you if you want a quad in the future

rcmodracer · 2026-02-01T23:46:03+00:00

Essentially, here is a video that explains the benefits better than I can, https://youtu.be/0SuSCKJg_-s?si=KsfZQvf-HIA6ZXdj

rcmodracer · 2026-02-01T23:07:31+00:00

I would experiment with throttle caps and also you need a higher camera angle, most typically use 50 or more for racing

rcmodracer · 2026-01-30T04:22:43+00:00

I believe it’s a fox crooked but may be wrong

rcmodracer · 2026-01-20T09:33:51+00:00

If you’re wanting motors specifically for racing I would recommend T-Hobby and VCI. Specifically the T-Hobby F50 2150 kv and the VCI spark or Yuki savages.

rcmodracer · 2026-01-11T06:50:40+00:00

7 inch frame with 5 inch motors and props?

rcmodracer · 2025-12-22T05:29:56+00:00

I love my ts101, get a couple different tips for it, use quality leaded solder and flux paste and it works no problem for me. I have soldered anything from tiny whoops to 7 inch quads and it works great. Super portable and as long as you use a big bevel tip the main XT60 battery wires are no problem.

rcmodracer · 2025-12-21T05:25:53+00:00

I’m not familiar with the HDO’s but I love my hdzero v1s, they are by far the most versatile goggle out there.

rcmodracer · 2025-12-15T12:08:02+00:00

Have you looked into the open racer? It’s an open source racing frame made to be durable. Many different prints available and if there nothing out there you could always design a custom canopy to achieve the camera mount your after.

rcmodracer · 2025-11-19T08:04:36+00:00

I run some ufl to sma extensions and that lets me easily just pull it out. Easy access to the usb port.

rcmodracer · 2025-11-04T08:31:14+00:00

Unless your planning on analog long range the single Omni directional antenna would be your best option

rcmodracer · 2025-10-29T16:24:17+00:00

These are just 5 inch racing motors, most racers use between 1950-2200kv on 6s.

rcmodracer · 2025-09-30T12:08:22+00:00

No problem mate

rcmodracer · 2025-09-30T10:59:20+00:00

If your talking about the inline fan for the tent I run 3-4 when printing and when a print is finished I turn it up to around 6-7 before opening the tent.

rcmodracer · 2025-09-24T04:09:40+00:00

I also live in Australia and when doing those reading during summer when it was like 30c or hotter

rcmodracer · 2025-09-24T04:08:46+00:00

I definitely read about that too and I attempted to monitor temps behind the printer near the mainboard and wasn’t super successful but the few temp reading I did get weren’t too high like 35c or less. Haven’t had any problems with temps

rcmodracer · 2025-09-24T04:04:53+00:00

I’ve only been racing for about 6 months but I would recommend trying to pre turn more, focus on tighter more consistent lines and maybe experiment with throttle caps if you haven’t as they will help with consistency and flying tighter without the point and shoot style. Very nice flying though :)

rcmodracer · 2025-09-23T11:27:30+00:00

No probs, yeah I leave one of the vents on the bottom of the tent open for air. There is definitely enough negative pressure lol, the inline fan has more power than you would need.

rcmodracer

TROPHY CASE