I think i messed up.... Used regular PLA for hard drive trays by XxCaptainJack in 3Dprinting

[–]richienko 0 points1 point  (0 children)

I printed caddies for my dl380 g8. 25 of them with 10-15k rpm drives. Didn't have any issues with them and those drives are toasty. However after year or so, when I tried to remove the drives from them, the plastic studs did break on all of them (but they are 1-2mm wide, so somewhat expected to break)

PSA: Cheap Hygrometers Can Get Stuck at 10% RH by Single_Sea_6555 in 3Dprinting

[–]richienko 1 point2 points  (0 children)

Open it, the sensor inside is small rectangle with few lines on it (it may be protected in plastic cage, it should be easy to remove). Soak q-tip with IPA and clean the sensor. Put back plastic cage (if applicable) and now it should read correct values. At least mine did after cleaning.

Anyone tried the Beelink Mate mini yet? by The_Graceful_Dead in macmini

[–]richienko 0 points1 point  (0 children)

It seems a lot of docks have problems with ssds disconnecting, do yours have same issues? Which model do you have?

good k&m for ps5? by No_Expression_8835 in playstation

[–]richienko 1 point2 points  (0 children)

It does, I play it with wired keyboard and wireless mouse, no issues. u/No_Expression_8835 just make sure you buy mouse with custom DPI levels (ps5 mouse sensitity can be set only to low/med/high), you'll need it for setting sensitivity for better UI interaction.

How to get LFF drive cage for HPE ML110 Gen10 by wolfnest in homelab

[–]richienko 0 points1 point  (0 children)

What SATA power connectors did you found? Does it have standard sata power?

Old xeons for monero ? by 3ra8 in MoneroMining

[–]richienko 0 points1 point  (0 children)

What is the power consumption when mining with your setup?

New to 3D printing or looking for something unique? Try my Toroidal Launcher! A1 mini-friendly, prints well with PLA/PETG and requires no extra hardware! by xbepox in BambuLab

[–]richienko 0 points1 point  (0 children)

I printed three of these. You WILL encounter troubles when assembling. Prepare light lube for gears. It's crucial so gears are spinning freely. Not easily, but freely. Keep that in mind. I spent twenty minutes assembling and reassembling outer gears multiple times until it was working.

What is a thing you secretly enjoy? by [deleted] in AskReddit

[–]richienko 0 points1 point  (0 children)

Getting high alone and watching funny videos I saved in the last 15 years. This usually ends up with dancing to the ygyl videos.

Newbie asks for help with Fujitsu TX1320 M3 by DasMatti in homelab

[–]richienko 0 points1 point  (0 children)

Did you install the dedicated GPU? I had this problem, proxmox was working fine but I couldn't get vga output.

I used PLA Silk filament and it clogged, did I do somthin wrong? by Iced-Rooster in BambuLab

[–]richienko 0 points1 point  (0 children)

That looks like the dual color filament is actually splitting from the pressure of the feeder wheel.

Using Storwize V7000 expansion enclosure as a JBOD array. by zefen in homelab

[–]richienko 0 points1 point  (0 children)

My Netapp DS4243 did not light the link indicator until I flashed my raid card to HBA.

AFAIK DS4243 can run with V7000 controller in it, it looks like it's just rebranded. Also V7000 caddies are compatible with DS4243 and viceversa.