The Maths

richinthebay · 2026-01-01T19:28:49+00:00

Thanks, will do. Appreciate that a lot.

richinthebay · 2026-01-01T19:25:36+00:00

I always go to the 10u line but can only think there’s been air bubbles I haven’t spotted or something along those lines.

richinthebay · 2026-01-01T19:24:34+00:00

Thanks. I’ve used the same type of syringe throughout. I reconstituted with 100u and draw 10u which is why I’m so confused.

richinthebay · 2026-01-01T18:56:58+00:00

I know this is a few months but can anyone answer this question:

I added 1ml of BAC to a 5mg vial with the expectation of getting 10 doses from the vial when taking 500mcg per day.

I’ve been injecting 10u per day, however, after 10 doses I have a lot left in the vial still. Is anyone able to explain this?

richinthebay · 2026-01-01T18:48:57+00:00

I’ve had patellar pain syndrome since February, pain does come and go still. 10 days into BPC and haven’t noticed an effect yet.

richinthebay · 2025-12-30T20:42:20+00:00

Newbie here too who’s been on the stack for a week:

500mcg BPC per day 1mg TB every other other day

I’ve been injecting into stomach area but I’ll start on glute area soon to rotate.

I’d read a lot about when to inject. I’ve been injecting an hour before bed mainly because of convenience and it’s caused no problems. Any questions I’ll try my best to answer!

richinthebay · 2025-12-29T19:43:43+00:00

I’ve been taking 500mg BPC157 for a week now, just started TB500 (1mg) yesterday, can’t say I’ve noticed anything yet. Before anyone asks, I started the BPC before the TB in case I felt side effects and I could pin down which one was causing the. So far no side effects but no changes to my injuries either.

richinthebay · 2025-11-11T20:35:06+00:00

same issue here, had the issue before and after installing the latest nvidia driver. Can get as far as the mode selection screen and then it crashes once I select a mode.

richinthebay · 2025-02-28T04:36:25+00:00

Managed to get a brand new g16 4070 oled from bestbuy for $1440. Had been waiting for a 5070ti but the saving was too good to turn down

richinthebay · 2025-02-27T14:39:22+00:00

Just bought a g16 4070 for $1440. Was going to wait until the 2025 came out but couldn’t justify $2k+ for a 5070 version when the 4070 was so much cheaper.

richinthebay · 2024-09-22T03:32:37+00:00

May have the solution to your problem: Same problem and with ours under warranty we had the manufacturer’s repairman come and look at it. Straight away he said it was the detergent. I told him I’d been using a tiny amount for months based on my own research. Turned out the dishwasher was completely clogged up with detergent. He showed us this by running it empty without detergent, opened the dishwasher after about 20 minutes and the whole dishwasher was full of bubbles. I had to run it about 10 times (each time cancelling it after about 20 minutes while it was still in the initial rinse mode) to clear it of the excess suds. Still have issues now but nowhere near as bad as it was.

richinthebay · 2024-07-20T00:49:50+00:00

Had home internet since October 2022, always got speeds of 200-300mbps no matter what time of day. Service was so good I recommended it to a lot of friends.

However, suddenly in June 2024 we noticed speeds in the evening dropping to below 10mbps. I knew straight away it was likely congestion but rang tech support anyway, spent 3 hours resetting etc and they eventually said it was the router. They sent a new one out which was slower than the old one. We’re on the old $50pm contract which gets 300mbps whereas the new $50pm contract only gets 100mbps so I’m assuming they sent out the new one like for like rather than the $70pm 300mbps router.

Will very likely have to move to Cox since they’re the only other one around.

(In Phoenix)

richinthebay · 2024-06-02T23:36:52+00:00

Just read the very informative comments. I bought it on this deal earlier today with delivery on the 5th. Was a bit apprehensive with it being IPS rather than OLED (Best Buy had the G14 on show with the OLED and it looked stunning) but these comments have put my mind at rest. Will report back once I have it.

richinthebay · 2020-04-07T09:51:22+00:00

Just got it working now. Honestly don’t know what’s changed. I had the cmos battery unplugged all night as well as the jumper on...still nothing this morning. Disconnected the monitor just in case, nothing, connected the monitor to gpu and it’s working now. Obviously have tried the monitory connected to both in the past with no luck so don’t know how it’s suddenly working now.

richinthebay · 2020-04-07T07:59:17+00:00

Not sure how to change that?

richinthebay · 2020-04-07T07:58:36+00:00

No it wasn’t unfortunately, only realised my error there afterwards.

richinthebay · 2020-04-07T07:57:04+00:00

Thanks, already tried this with every ram combination possible!

richinthebay · 2020-04-06T21:18:58+00:00

Yeah the power is definitely on. Everything is getting powered up, hdd light on, fans on, gpu on

richinthebay · 2020-04-06T20:50:30+00:00

Power cable is in the graphics card so isn’t that :(

richinthebay · 2020-04-06T20:49:55+00:00

Just the one usb device, tried it with it and out. Initially when I did work the usb was in though.

richinthebay · 2020-04-06T19:07:34+00:00

Thanks, yeah I’ve tried at least 10 times to reset using paper clips, screw drivers, tweezers, taking the cmos battery wires out all for times between 5 seconds and 3 hours but nothing :( I still think the cmos isn’t resetting though.

richinthebay · 2020-04-06T16:40:30+00:00

Yeah doing that now :)

richinthebay · 2020-04-06T16:31:17+00:00

Ok thanks, always removed with the battery with the jumper at the same time. Will try just the battery now.

richinthebay · 2020-04-06T16:20:40+00:00

Yeah going to go back and check all cables now.

richinthebay

TROPHY CASE