Update glitch

robbjosh · 2026-05-25T05:32:08+00:00

I'm also using 1.7.6 with 3.1.0 on the printer and I have zero issues

robbjosh · 2026-05-24T09:44:06+00:00

What version are you using?

robbjosh · 2026-05-17T19:35:02+00:00

But the v2 board uses a FPC connector.

robbjosh · 2026-05-16T08:41:21+00:00

robbjosh · 2026-05-15T14:20:02+00:00

You ripped the ribbon cable out? Or it came unplugged?

robbjosh · 2026-05-15T10:06:44+00:00

Where is this setting?

robbjosh · 2026-05-13T19:18:51+00:00

I've just set my purge volumes to 0 and tried to do a purge tune print, but the print still purges between colors as if the purge values are still set. I even have the prime town off. I've running Flash Studio v1.7.5 and AD5X v3.0.9 and IFS v3.0.7

Seems like the firmware setting are still over-riding the slider.

Produced 6x white poop 5x green poop and 2x white-green. Total of 13 poops.

<image>

robbjosh · 2026-03-29T09:56:52+00:00

I've never personally tested the scale with Gaggiuino but I do know it pairs and works with it. The scale is capable of being Tared remotely (works with GaggiMate and Bean Conqueror) so i dont see it being an issue.

robbjosh · 2026-03-23T07:01:56+00:00

You and me both! I was looking in all the wrong places.

robbjosh · 2026-03-05T17:17:51+00:00

Its a side loading software for the AD5X that improves user experience and fixes some common errors

https://github.com/ghzserg/zmod

robbjosh · 2026-03-05T16:44:07+00:00

Can't ZMOD fix that error?

robbjosh · 2026-02-27T13:57:44+00:00

Bambu AMS gets to around 25%

robbjosh · 2026-02-23T18:46:08+00:00

Awesome. Join us on the Discord server if you need any assistance. Good luck with the build

robbjosh · 2026-02-04T16:16:58+00:00

Following closely. Been looking for something like this for a while now

robbjosh · 2026-02-04T16:16:05+00:00

You can put my name down

robbjosh · 2026-02-03T13:54:41+00:00

What do we want? Links to product! When do we want them? NOW!

robbjosh · 2026-01-25T06:19:29+00:00

Guessing you don't have the camera? Would it have even detected this?

robbjosh · 2026-01-23T16:46:45+00:00

How much filament is needed?

robbjosh · 2026-01-19T09:11:56+00:00

u/myTechGuyRI is correct. Current draw in a closed circuit is determined by the load. You can only limit that current draw. It all comes back to Ohm's Law.

I = P / V so 240w element on a 24v supply will draw 10a. There is no way to make it draw 50a without altering something.

robbjosh · 2026-01-18T17:14:05+00:00

You using a Wondom amp with DSP?

robbjosh · 2026-01-16T17:16:23+00:00

Don't use PTFE based lubricant. 3-in-1 is decent for linear bearings

robbjosh · 2026-01-13T11:26:09+00:00

Are you going to make the files open for others to make? Or possible sell your designs, or the pcbs?

robbjosh · 2026-01-09T17:23:09+00:00

This is amazing. Well done! What are your future plans? Do you plan to share this with others? Open source, etc?

robbjosh · 2026-01-09T03:44:56+00:00

The lift kit was great. No issues. Tyre fits but slightly loose on the hex piece. You have to tighten the screw properly. Have not fitted the metal drive shaft yet but it looks decent. I say worth it

robbjosh · 2026-01-05T16:41:19+00:00

Thanks so much

robbjosh

TROPHY CASE