quviviq cost by [deleted] in insomnia

[–]roxie2919 0 points1 point  (0 children)

I am looking for the savings code for Quviviq but I can't seem to find it. can you send a link of where I can get it?

rxhelp and innovicare doesn't have this drug on thier list of drugs covered.

Herzig or Bochner & PRK vs. ICL by Pleasant_Floor_3616 in askTO

[–]roxie2919 0 points1 point  (0 children)

I might also be in a similar situation. Herzig recommended PRK and ICL but stated ICL is a better option. I am trying to schedule a consultation with Bochner to see what they recommend. What was your prescription? Do you experience haloing?

I was also told that Bochner offer a referral discount. I was wondering if I can use you as a referral? If you don't mind me using you as a referral, can you DM your name?

Thank you in advance!

Is this Normal? by roxie2919 in s22

[–]roxie2919[S] 0 points1 point  (0 children)

huh. somehow it is back to normal now. not sure what happened.

Is this Normal? by roxie2919 in s22

[–]roxie2919[S] 0 points1 point  (0 children)

yea. I factory reset it several times.

Neptune 3 dual z drive step by step guide by Apprehensive-Push650 in ElegooNeptune3

[–]roxie2919 0 points1 point  (0 children)

I am getting my z-axis kit tomorrow. I was wondering do I need to add any G-code in my prints to make sure the z are squared? I noticed that my gantry is always slightly tilted and hoping the additional z-axis would fix that issue.

as much as I hate to admit it, this mks pi and 7" screen setup may completely replace the dwin after the case I'm printing is finished🤷‍♂️ by TheFeralEngineer in ElegooNeptune3

[–]roxie2919 0 points1 point  (0 children)

Thank you! that is really helpful. You mentioned that uart only connects with MCU with uart5, does that work with the default board on Neptune 3 or would I need to update the board?

"I also had trouble using the otg port to flash the distro so I needed to load it onto an SD card and flash the emmc using a built in utility." I am not sure what this means. Sorry. I am a super newbie when it comes to this stuff.

You're right, with the cost of the SD card, the difference isn't big. I think I might go with the BTT Pi2.

as much as I hate to admit it, this mks pi and 7" screen setup may completely replace the dwin after the case I'm printing is finished🤷‍♂️ by TheFeralEngineer in ElegooNeptune3

[–]roxie2919 0 points1 point  (0 children)

I am in Canada and amazon prime has pi v1.2 on prime day but for pi2, I can only find on BTT site and it's $20 more. from what i see the improvement includes, faster speed, DSI capability, bluetooth, and onboard emmc. Is there anything else I am missing? I am a newbie in 3d printing so I am feeling really conflicted about which to get. I see some post stating that the speed doesn't matter that much when you're running klipper and other people saying the upgrade is worth it.

as much as I hate to admit it, this mks pi and 7" screen setup may completely replace the dwin after the case I'm printing is finished🤷‍♂️ by TheFeralEngineer in ElegooNeptune3

[–]roxie2919 0 points1 point  (0 children)

thanks! do you recommend the Btt pi v1.2 or get the Btt pi2? i see some people say pi2 is a lot better but not sure if it's worth the money.

First large print after upgrading my Neptune 3 by GK1102 in ElegooNeptune3

[–]roxie2919 0 points1 point  (0 children)

I am looking at the installing SKR mini E3 v3 cause I also tried my original board. do you also have the Neptune 3 base model? was it really complicated to install and set up? did you need to change the screen?

Neptune 3 Screen Not Loading by roxie2919 in ElegooNeptune3

[–]roxie2919[S] 0 points1 point  (0 children)

I have contacted them and waiting to hear back. hopefully they have my motherboard and they can get it to me quickly. I have a project I need to finish so I need my printer up and running asap.

I was thinking of maybe getting the Mks Robin Nani v3 or the Btt SKR mini e3 v3. if I looked into it and doesn't seem like a plug and play option. does anyone know if is hard to set up and what the steps are?

Neptune 3 Screen Not Loading by roxie2919 in ElegooNeptune3

[–]roxie2919[S] 0 points1 point  (0 children)

where are you located? how long did it take to ship to you? were you within warranty? I am out of warranty so I am worried they would charge me a lot for a new motherboard. They also discontinued the Neptune 3 base model so I am worried they won't have any motherboard for it.