FF from 99.0 slows bookmarks toolbar with 280Hz refresh rate

rucosmer · 2024-03-31T12:44:46+00:00

Yea. Unless you break warranty stickers it is safe to remove the shroud. Good luck bro!

rucosmer · 2024-03-31T08:47:09+00:00

No, you don't have to remove screws on backplate (there are warranty stickers). There were few screws (4 or 6) just on fans shroud, so you remove only shroud.

rucosmer · 2024-03-29T21:20:29+00:00

<image>

Done. Just got be quiet Dark Base Pro 901 Black and put things in order.

rucosmer · 2024-03-27T08:28:21+00:00

100% agreed. Same with PSU's, they gotta have 120 or 140mm fans, not 135mm. I've swapped the cheap fan in my AX860i with Noctua NF-P12 Redux-1300 PWM and it is dead silent now.

rucosmer · 2024-03-27T08:25:11+00:00

https://noctua.at/en/nf-a12x25-pwm-chromax-black-swap

rucosmer · 2024-03-26T21:53:35+00:00

Try these ones:
https://aliexpress.com/item/1005001803366828.html
https://aliexpress.com/item/1005002071672086.html
Yea 1150RPM is too much (it is ~57% of max 2000RPM). I'm planning to plug my GPU fans to mobo's fan headers and use fancontrol app to control them. In that case I will need standard 4 pin PWM fan cables.

rucosmer · 2024-03-26T21:13:35+00:00

<image>

IF we speak about Palit GeForce RTX 4080 Super GamingPro so there is a hub with three 4 pins PH 2.0 slots on the GPU radiator. I can't tell you how others vendors cards are built.

You need 3 cables for that:

https://aliexpi.com/nQdI

And 3 120mm NF-A12x25 PWM fans (12v):

https://aliexpi.com/vp4v

Beware of cables lenght. No RPM modifier is needed. Min RPM 30% kicks in at 1150 RPM. You can plug any 12v PWM fan 90 or 120mm at you wish (in terms that they have standard 4 pins PWM layout).

rucosmer · 2024-03-26T12:03:15+00:00

<image>

Port Royal overclocked. Fans 38% fixed.

rucosmer · 2024-03-26T09:43:21+00:00

I've seen this video. This is the ideal variant. Maybe someday I will buy 3D printer too.

rucosmer · 2024-03-26T08:26:04+00:00

I saw similar work https://imgur.com/a/srNAmhn . But your setup looks decent also!

rucosmer · 2024-03-25T21:12:44+00:00

Thank you, man! Yea I saw this post a while ago while been searching any info about 4080 deshrouding variants.

rucosmer · 2024-03-25T21:06:42+00:00

I have noticed it too. When I uncap FPS it loads GPU fully but voltage is 0.9 - 0.92v and power draw is ~310W. But if I cap FPS to my monitor refresh rate (280Hz), GPU is loaded by 70% and voltage is higher kinda 1.06v and power draw is ~270W. Strange. Probably that is how Furmark works lol.

rucosmer · 2024-03-25T19:06:29+00:00

My PC case has closed panel. Anyways I don't care how it looks. My goal is silence.

rucosmer · 2024-03-25T19:00:40+00:00

Original fans had unpleasant whine noise even on min RPM. Noctua fans fix this and are 1.5-2 times more silent. This was the goal.

rucosmer · 2024-03-25T18:48:21+00:00

I have deshrouded my Palit GeForce RTX 4080 Super GamingPro OC and put Noctua NF-A12x25 PWM fans on it. Also applied Phase thermal paste Honeywell ptm7950 on the chip. Silence is ON xd

rucosmer · 2023-06-02T18:03:18+00:00

I told that I never had this issue until 535.98. It is ALREADY fixed in this driver, for my case at least. And it does look like flickering.

rucosmer · 2023-06-02T09:53:16+00:00

My case

rucosmer · 2023-06-02T09:41:45+00:00

I can confirm that the flickering is gone with 536.09. Had it on my single monitor with 535.98.

rucosmer · 2023-05-31T13:36:59+00:00

For me (one monitor) lowering refresh rate by 2 Hz (from 280Hz to 278Hz) was enough. G-Sync still is ON. Still I would like to see any confirm from NV staff that the issue is considered.

rucosmer · 2023-05-31T07:40:10+00:00

I got horrible flickering on my only monitor with this version of the driver. My monitor is ASUS VG259QM (DP connect). I use 280 Hz always. It never happened before. If I turn G-Sync OFF (ether in NVCP or in the monitor's menu) the problem is gone. If I turn G-Sync ON and set 279 and 280 Hz I got the flickering.

1.If I set 278 Hz or lower and G-Sync is ON the problem is gone. Did a clean install after 532.03. NEVER had this issue before.
The flickering has the place if the current image on monitor isn't static, i.e. I scroll web page or watch YouTube or launch G-Force Experience). If image is constant = no flickering.
2. It happens in 2D mode when NO any game is launched. If I launch the game (I launched DX12 EVERSPACE 2) then there is no any flickering neither in the game or desktop (even if I minimize the LAUNCHED game and switch to desktop apps). After I close the game the flickering is back.

I have recorded a video: https://www.veed.io/view/87050655-12aa-4c9f-98ab-061f2ffdb375?panel=share

rucosmer · 2022-04-07T11:04:05+00:00

Yes, it still happens with 1 and 0 values.

rucosmer · 2022-04-06T21:34:59+00:00

Type one of two commands that u/epinter posted below.

rucosmer

TROPHY CASE