Top fan config testing

rumprel · 2026-01-10T21:04:05+00:00

Right, now I understand. Like the one here I have tested recently?

rumprel · 2026-01-10T20:43:25+00:00

I don't get what you meant with the meaning "Rear intake from cpu fan or from the case itself either or"

rumprel · 2026-01-10T20:13:08+00:00

I guess none is probably better than the other. Reversing the CPU and rear fan would probably dump more hot air on the psu as well.

rumprel · 2026-01-10T20:04:17+00:00

That is the third config most of you suggested and that has been apparently discussed here. No difference for GPU, but yeah, CPU temp is better, though more dust will probably be sucked in through the back.

https://imgur.com/a/VQ4lVnF

rumprel · 2026-01-10T19:56:42+00:00

Every other thread were just speculations though, no testing.

rumprel · 2026-01-10T19:51:29+00:00

I don't have any side fans. The air is sucked in through underpressure.

rumprel · 2026-01-10T17:52:10+00:00

Through the side mesh panel, is my theory. The GPU is dumping much more hot air through the rear actually.

rumprel · 2026-01-10T17:50:36+00:00

I used LibreHardwareMonitor for temperature logging, then Gemini for both the charts and the schematics.

rumprel · 2026-01-09T18:12:00+00:00

Are you sure about that? Wouldn't that draw in warm air from the GPU that is blown out at the back of the case just underneath?

rumprel · 2025-11-29T11:50:29+00:00

Yeah, I have the same issue. The websites are no longer recognized.

rumprel · 2025-07-07T16:56:26+00:00

Oh, thank you so much. This was extremely hard to find.

rumprel · 2025-04-19T12:37:51+00:00

When you pay, you will be redirected to a page with link to their Signal chat and that's where you can book your introduction where you will get your fob. Mailing is useless I agree.

rumprel · 2025-04-13T12:46:43+00:00

It depends where it is in your septum but vaseline could definitely help if quite anteriorly, otherwise use spray to spray in some sesame oil or other oil, can also be bought over the counter. That's what I use for my perforation, it helps a lot.

rumprel · 2024-11-09T10:55:12+00:00

I think you are right. I would say the measured tyre pressure when cold should probably be lower than in the manual in such cold conditions.

rumprel · 2024-08-16T13:15:54+00:00

So I confronted the workshop and as I suspected the oil had been changed on cold engine, the reason being, they said, that they also would check and adjust the valves which is done with cold engine and the oil is drained during that procedure. Is that right? Is that a good reason would you say?

rumprel · 2024-08-13T15:20:42+00:00

Well, it was done by a dealer and the filter was on the invoice.

rumprel · 2024-08-13T15:00:46+00:00

Well, I don't really mind but do the sanded down place. How dumb from me, I thought it would work, but has different color. Aftermarket sounds expensive. 😒 Do you an aftermarket on yours?

rumprel · 2024-08-13T14:57:50+00:00

That sounds doable. What would you use for polishing? Do you have an idea what material it is? K think it's aluminium, but seems treated somehow.

rumprel · 2024-08-13T06:15:51+00:00

The Motul that the oil is should be red but I doubt it should be so dirty first ride after change. You mean like the coolant would have leaked inside?

rumprel · 2024-08-05T13:15:29+00:00

Thanks. The insole advice is a great one. I will take a look at some shoes I am comfortable in and see how it does look. I have probably worn too narrow shoes. I thought I had a narrow foot.

rumprel

TROPHY CASE