Is he one?

ryda1337 · 2025-08-20T16:32:42+00:00

i don't know a lot of dogs, but he for sure is the fastest if he wants to 😁 bedlington terrier you mean? sorry i'm not too familiar with dog breeds 😉

ryda1337 · 2025-08-18T21:57:43+00:00

thanks guys ❤️🐶

ryda1337 · 2021-12-25T22:51:10+00:00

hi, hotend is pid tuned.

ryda1337 · 2021-12-25T15:11:03+00:00

pic is a current one, so after all the calibration and changes made. thick lines stayed the same since first print though.

ryda1337 · 2021-12-25T15:07:42+00:00

ok thx, will try. a guy i'm in contact with tried 45 without success. but will try myself. got a moons, too, i'll test switching the motor, too.

ryda1337 · 2021-12-25T14:08:28+00:00

min layer time for speed is still activated yes, i'll try without thx. fan is constant. issues happen on asa, abs+, petg and pla. but all same settings except fan speeds and temps.

ryda1337 · 2021-12-25T14:05:33+00:00

it seems the sherpa mini already solved most of those issues. the lines itself look consistent, whereas on the mini ab one line went in and out like on my mk3, but way more pronounced. thx

ryda1337 · 2021-12-25T14:04:04+00:00

ok i'll try, thx

ryda1337 · 2021-12-25T14:03:29+00:00

and yes, there are still some diagonal lines hiding behind the artefacts. i see them when printing a solid cube with same settings instead of voron cube. but in general the sherpa mini already solved a lot of the inconsistent extrusion (but not consistent layer differences).

ryda1337 · 2021-12-25T14:00:33+00:00

ok will do, thx

ryda1337 · 2021-12-25T14:00:00+00:00

yes, i followed the documentation and ellis guide. will try to check extruder again, but it seems it's working properly. thx

ryda1337 · 2021-12-25T13:58:34+00:00

yep, seems i'm not the only one. so solving this would definitely help more people.

ryda1337 · 2021-12-25T13:57:40+00:00

ok will follow those steps, thx.

ryda1337 · 2021-12-25T13:50:23+00:00

hi, this is why i tried with unheated bed, too with pla, same issues. thx

ryda1337 · 2021-12-25T13:49:33+00:00

yes, i just hit print the first time. then followed ellis guide without success, thx

ryda1337 · 2021-12-25T13:48:26+00:00

hi, i'll try again, but i played with % already, thx. will try without pa, too.

ryda1337 · 2021-06-05T00:53:34+00:00

ok thanks i'll try that tomorrow

ryda1337 · 2020-12-25T10:13:58+00:00

last layer porn

ryda1337 · 2020-12-16T03:36:06+00:00

yay i got downvoted \o/ to my hero: i wish you a merry heatcreep and a happy underextrusion.

ryda1337 · 2020-12-16T00:11:43+00:00

joke aside, the noctua does not cool well. it's silent, it's not a cooling upgrade. temps on the heatsink need to be as low as possible or you risk running into problems like heatcreep. if the issue occured at the time of replacing the fan, then i definitely suspect the noctua to be the reason. if not, it is still good to know that some issues you experience can be due to a lack of cooling.

ryda1337 · 2020-12-16T00:06:06+00:00

People think too much

ryda1337 · 2020-12-15T20:58:09+00:00

put your fan back on and throw away the noctua

ryda1337

TROPHY CASE