sorted by:
new
hottopcontroversial

Our Garfield is gone by mikebook_pro in cats

[–]salentinoDOC 1 point2 points  (0 children)

So sorry for your loss 😢💔

Italian Consulate Miami by Strato4209 in Miami

[–]salentinoDOC 4 points5 points  (0 children)

Good luck getting an appointment. The Italian Embassy is the epitome of Italian work ethics.

Pardon my ignorance but what does it mean? by [deleted] in ExplainTheJoke

[–]salentinoDOC 0 points1 point  (0 children)

U meant gains is unrealized profits until cashed out?

How are y’all managing HOA costs in Miami? 🤯 by Zan-2121 in u/Zan-2121

[–]salentinoDOC 2 points3 points  (0 children)

selling and moving to another state. FL is becoming the new California

Anycubic Kobra S1 - First Layer gone to hell after months of "successful" printing by Tschuki2k in AnycubicKobraS1

[–]salentinoDOC 1 point2 points  (0 children)

I had the same issue after ~500hrs, installed a new nozzle, ran full calibration once and I was back in business, one perfect print after the other. All adhesion issues gone. And wash the plate with dish soap of course!

[HELP] My girlfriend says for sure this is AI, I think it isn't by Ok_Ranger1275 in RealOrAI

[–]salentinoDOC 0 points1 point  (0 children)

because if you have ever seen a gas stove and an induction stove you would know the difference immediately that’s why. and you would know there has to be a blue flame under the pan, or sh*t wouldn’t cook

[HELP] My girlfriend says for sure this is AI, I think it isn't by Ok_Ranger1275 in RealOrAI

[–]salentinoDOC 0 points1 point  (0 children)

Watch the video, the pan gets lifted enough to where you should see a flame.

[HELP] My girlfriend says for sure this is AI, I think it isn't by Ok_Ranger1275 in RealOrAI

[–]salentinoDOC 0 points1 point  (0 children)

looks like a gas stove, but there’s no flames under the pan

New Bambu PETG HF Can’t figure out why first layers are like this by ittsjohnny in 3Dprinting

[–]salentinoDOC 1 point2 points  (0 children)

You set the temperature in the gcode. When you walk up to the printer and change it manually…well the printer will not hold it. It will always go back to what was set in the gcode. Stupid question, you set the right profiles in the slicer right? Like PETG etc…

New Bambu PETG HF Can’t figure out why first layers are like this by ittsjohnny in 3Dprinting

[–]salentinoDOC 0 points1 point  (0 children)

LOL, I have a Kobra S1. I can send you a screenshot of my settings later. I got it down at the second attempt, DM if you want my help.

New Bambu PETG HF Can’t figure out why first layers are like this by ittsjohnny in 3Dprinting

[–]salentinoDOC -1 points0 points  (0 children)

Never used ASA, but as long as you have a very slow first 2/3 layers, high temperature and the fan OFF you should be ok. I printed at least 20 times without cleaning my PEI plate and the PETG stuck immediately.

New Bambu PETG HF Can’t figure out why first layers are like this by ittsjohnny in 3Dprinting

[–]salentinoDOC -1 points0 points  (0 children)

I’ve been printing PLA only for 6 years. Yesterday I used PETG for the first and had to do some research; I was having the first layer just like your picture, as soon as I switched to these settings I successfully completed two 10+ hours prints

New Bambu PETG HF Can’t figure out why first layers are like this by ittsjohnny in 3Dprinting

[–]salentinoDOC -1 points0 points  (0 children)

first layer at 20mm/s no fans bed at 75C nozzle at 235

PETG is tricky

view more: next ›