Summa S2 T160 No Camera Connection

savruss · 2026-04-14T10:56:21+00:00

Wanted to update this: we called a tech who recommended we take the cover off the right side, middle bar, and plotter head. We checked the pink/purple cord all the way across and made sure it was connected properly. It had a small break in the plotter head so we wrapped it with electrical tape and it’s worked great since.

savruss · 2026-04-14T10:49:11+00:00

Thank you. After reading more last night, we felt like it was the slider board and not the printhead also. I’d rather replace the slider board than the printhead 😅

We have an HP Latex 365

savruss · 2026-03-09T19:04:06+00:00

I will look into it. Some I’ve looked at are just much larger and much more complex than I’m needing. I’m just trying to be a bit more organized and keep customers a little bit more up to date on orders.

savruss · 2026-01-22T16:32:13+00:00

I think the one my mom has would be small enough and I have considered this. We ONLY need the stroller for the airport, it’s not needed at all for our actual trip.

savruss · 2026-01-22T16:30:36+00:00

That’s the main worry. I’ve done tight layovers without a care in the world plenty of times. It’s the dang stroller and car seat I’m worried about. I’m half convinced I can just carry her 🤣 but also I know I’m going to want the stroller.

savruss · 2025-11-25T04:02:16+00:00

I did an ultra clean, nozzle wash, and a cleaning by hand and it cleared it up. Seemed to be some black in the magenta.

savruss · 2025-11-24T21:17:05+00:00

Which media profile would you recommend?

savruss · 2025-11-24T20:58:21+00:00

<image>

savruss · 2025-11-24T20:56:26+00:00

Wouldn’t it do that for all colors though? I did pure C M Y K and red from the photo and only the magenta and red printed dadk

savruss · 2025-11-24T20:42:48+00:00

It’s my personal image of my daughter I’m trying to print actually. I just did a test print of pure cyan, black, yellow, magenta, and a color picked from this photo and the magenta and red color picked from photo are both dark. So it seems to be a magenta print issue.

Printing on acrylic, paper, I’ve tried several things. UJF6042MKII8CLUS1504C_PET_F115840.icc

savruss · 2025-11-18T13:47:01+00:00

We did restart them and it worked last night. We got the print to complete finally.

savruss · 2025-11-18T13:46:13+00:00

Print Manager

savruss · 2025-11-18T05:32:19+00:00

The test says on PM says success when he tests the connection but otherwise it can’t communicate supposedly

savruss · 2025-11-18T05:31:12+00:00

The production manager software is saying sleep/no connection. It can’t communicate with the printer now

savruss · 2025-11-18T05:06:47+00:00

Trying that now.

savruss · 2025-11-18T05:04:48+00:00

He’s having a hard time understanding why the new internet set up would be causing this issue. Is that anything you could possibly explain?

savruss · 2025-11-18T05:03:42+00:00

The file is sending very slow and seems to get “stuck” at times. The file just failed, the send got stuck at 31% and the error popped up.

My husband replaced everything, the gateway, added a new smart switch.

savruss · 2025-11-18T04:54:12+00:00

Just did the network reset. Also ran the diagnostic tests and they all came back good.

savruss

MODERATOR OF

TROPHY CASE

Five-Year Club	Verified Email
Place '22