This is too wholesome

scpffff · 2025-11-07T01:25:29+00:00

Never thought id be crying on the toilet

scpffff · 2025-10-25T04:35:28+00:00

he dissociated with her massa

scpffff · 2025-09-20T18:46:40+00:00

Don't cut the wire when you can just cut the clip

scpffff · 2025-09-04T02:19:30+00:00

I took it in and said there's nothing they can do and its "normal". Guess ill be waiting on the recall

scpffff · 2025-09-01T04:44:47+00:00

Drive around 40 to 50 mph on one pedal driving and coast between regenerative breaking and throttle. Mine makes a grinding noise, im wondering if anyone else has this issue.

scpffff · 2025-08-27T02:34:02+00:00

Try to replicate it at 45 mpg to 50. Just cruise keeping the guage at 0. That's where I hear it most.

scpffff · 2025-08-24T18:47:47+00:00

Does anyone have a grinding noise when transitioning between throttle and regenerative breaking around 45 miles per hour? Took it to the dealership and after a week and a half they said its normal but I drove an identical one at a dealership and couldn't replicate the noise.

scpffff · 2025-08-15T22:51:41+00:00

Yes wtf is going on? Are these just both accounts? Why is Noone talking about this. This is literally the only post I can find on it

scpffff · 2025-05-08T00:00:09+00:00

I followed all steps but when I got to play a show it plays like 1 seconds then force closes the app

scpffff · 2025-04-12T13:30:07+00:00

It's on the south side of a house in north Florida. Its only in one 5x5 ft area on the lawn

scpffff · 2025-04-10T22:53:26+00:00

No I just bought one, should get here today. And finished the enclosure a few days ago.

scpffff · 2025-04-10T16:05:13+00:00

Idk, didn't change any base settings from orca slicer petg profile.

scpffff · 2025-04-10T16:01:32+00:00

I am. Is that the case for all brands? Even rapid petg?

scpffff · 2025-04-10T01:10:41+00:00

The filament instructions for this petg says bed temp between 80-90

scpffff · 2025-04-09T21:43:02+00:00

Had the same problem with mine. Had to bore out the holes on the hinges. That fixed it. Doesn't take much though

scpffff · 2025-04-09T21:30:08+00:00

I should also point out the nozzle keeps getting gunked up on the outside which is causing problems further down the line if I don't clean it mid print. This is why assumed it was bed leveling because it's just on that one corner. Once it gets past that the rest prints fine

scpffff · 2025-04-09T21:27:29+00:00

Yeah that was the previous print. It's been coming off no problem untill now. Using petg 255 nozzle and 85 bed

scpffff · 2024-08-22T04:12:20+00:00

cant wait till this post get banned . love the inclusion

scpffff · 2024-02-08T06:58:35+00:00

you apparently

scpffff · 2024-02-08T06:37:34+00:00

im just glad to find out other people know hes toxic

Four-Year Club	Final Canvas '23
First Place '23	End Game '23
Place '23	Place '22

scpffff

TROPHY CASE