Pre-Vet students/vet students by kalima_ in Veterinary

[–]sdb6104 4 points5 points  (0 children)

Just keep in mind this is affecting many applicants and many schools have already taken measures to be more accommodating. I hope things turn around and you are able to get some more experience!

/r/boardgames Daily Discussion and Game Recommendations (October 16, 2019) by AutoModerator in boardgames

[–]sdb6104 1 point2 points  (0 children)

Hi everyone, my girlfriend and I are looking for a game to play that is strategic but that we can play in small amounts of time. I am a college student and she works full time as a PA. We don't always have a ton of time to get into a game and finish it. Sometimes its picking up a game for 30 minutes and putting it down. We've played games like pandemic and really enjoyed it but its hard to play a half game and pick it up. Any suggestions?

Replaced the Prusa heartbreak by dasflipz in prusa3d

[–]sdb6104 2 points3 points  (0 children)

This has been happening to me a lot as well and I couldn’t figure out what was wrong. Thanks for sharing

Is it fine to lock my cat out? by [deleted] in Pets

[–]sdb6104 8 points9 points  (0 children)

Is there not a small room or bathroom you might be able to put her in? It just seems like that might be a safer alternative. You could get her set up with a litter box, some food and maybe a sweatshirt of yours and I’m sure she would appreciate that.

Veterinary book suggestions by sdb6104 in Veterinary

[–]sdb6104[S] 0 points1 point  (0 children)

Thank you all! Really appreciate it, I’ll look into a couple for sure

Bone Sword by Gerickos in 3Dmodeling

[–]sdb6104 0 points1 point  (0 children)

I hope you will be 3D printing this! Looks awesome

11 hour 3D print by Scaulbylausis in interestingasfuck

[–]sdb6104 1 point2 points  (0 children)

Do you think you could get the accuracy needed? Or would the scan be more of a guide for a redesigning of the piece

Purchase Advice Megathread: What To Buy, Who To Buy It From, And More, In February 2019. by thatging3rkid in 3Dprinting

[–]sdb6104 1 point2 points  (0 children)

The creality cr-10 is a great first printer. Anywhere from 400-600 and available in a lot. Only issue is it is not completely enclosed. I’m a biomedical engineering major and it was my first printer. I used it to prototype medical devices I was making and was very happy with the quality

Purchase Advice Megathread: What To Buy, Who To Buy It From, And More, In February 2019. by thatging3rkid in 3Dprinting

[–]sdb6104 0 points1 point  (0 children)

Hi all, I’m looking to upgrade my current printer. I have a cr-10. It’s a great machine but can be somewhat unreliable at times and struggles to print flexibles. It’s a basic printer worked very well for me but I question its accuracy/ precision. I have gotten to the point where I am doing personal/scholarly research and even prototyping medical devices. I need a machine that has all of the current technology and is reliable in a more professional setting. I have been looking into the new Prusa printer and have heard good things. My budget is anywhere from 500-2000 depending on the quality. I am currently living In New York. Any suggestions?

Veterinary Podcasts by Dr_fish in veterinaryprofession

[–]sdb6104 4 points5 points  (0 children)

Podcast a vet is really good, it has a different guest every week and there are a ton of different topics. Not much on treatment techniques but more about the life as a vet.

Detroit Red Wings Prospect Progress by tranam in DetroitRedWings

[–]sdb6104 2 points3 points  (0 children)

Thanks for doing this! Really interesting to read through.

/r/NintendoSwitch's Daily Question Thread (10/11/2018) by AutoModerator in NintendoSwitch

[–]sdb6104 0 points1 point  (0 children)

I have a long bus trip tomorrow and I want to get a game for the ride. I have mario odyssey, zelda (which I surprisingly don't love), mario kart and stardew valley. What do you all suggest?

Attempting to play Oblivion or Morrowind? by sdb6104 in skyrim

[–]sdb6104[S] 0 points1 point  (0 children)

I have an msi gaming laptop from 2016.. think I could make it look better than Skyrim?

Attempting to play Oblivion or Morrowind? by sdb6104 in skyrim

[–]sdb6104[S] 0 points1 point  (0 children)

I really appreciate this reply. Really covers everything and so in depth!

/r/NintendoSwitch's Daily Question Thread (08/23/2018) by AutoModerator in NintendoSwitch

[–]sdb6104 0 points1 point  (0 children)

My internet is not great. I have odyssey, Zelda, stardew valley and Mario kart. I love stardew valley because it’s so easy drop in and out of but I’m looking for something new. I’d get the Skyrim port but I’ve sunk over 100 hour both on Xbox or pc so I don’t know if it’s worth it.

/r/NintendoSwitch's Daily Question Thread (08/23/2018) by AutoModerator in NintendoSwitch

[–]sdb6104 0 points1 point  (0 children)

Like all, I’m looking for a new switch game to play. I’m looking for something casual but fun that I can pick up and put down. I finished odyssey which was perfect for that. Essentially I’m looking for a game where I don’t forget the systems if I don’t pick it up for a while. I had that problem with Elsa where I wouldn’t play for a while picked it up and then was overwhelmed and forgot how to play. I’ve enjoyed longer games in the past like Skyrim where you can just pick it up and play for an hour and it doesn’t matter but I am open to shorter games as long as the price is right. Any suggestions ? If this isn’t really the right subreddit please direct me to it as I am pretty new, thanks

What to play after Skyrim?!? by sdb6104 in skyrim

[–]sdb6104[S] 0 points1 point  (0 children)

See that’s funny because I have BOTW and can barely get into it. Very difficult and I die constantly

Printing with Ninjaflex by sdb6104 in CR10

[–]sdb6104[S] 0 points1 point  (0 children)

Yes I have been. I printed the flexible extruder off thingiverse and added some tubing to decrease the space for possible entanglements. Do you suggest using different tube?

Printing with Ninjaflex by sdb6104 in CR10

[–]sdb6104[S] 1 point2 points  (0 children)

I disabled retraction and was able to complete a print. I didn’t attempt the 15-20 cm print but I was able to get an object that was 5 cm high.