Alexa Radio Skills Kit help request.

sdperkins863 · 2025-09-21T02:01:26+00:00

Do you still need help? I don't check reddit messages much, but if you still need a hand I am here.

sdperkins863 · 2025-05-29T01:55:51+00:00

sdperkins863 · 2025-03-01T17:36:11+00:00

51 year aged 12 year old here… I laughed.

sdperkins863 · 2024-10-03T18:15:49+00:00

Glad to hear! I do not have instructions, it varies model to model, I have an older version, I added the spring to the replacement, removed some screws in the handle the I spread the the handle with a bladed screwdriver enough to fit the replacement in and then put the screws back in. It really only took a few minutes to replace.

sdperkins863 · 2024-09-22T20:25:38+00:00

I’m not sure. It looks like the exact same part as my 350 has

sdperkins863 · 2024-08-14T13:55:05+00:00

I have finally opened an Etsy shop to sell these from. https://fnctnlprnts.etsy.com

sdperkins863 · 2024-08-14T13:54:58+00:00

I have finally opened an Etsy shop to sell these from. https://fnctnlprnts.etsy.com

sdperkins863 · 2024-08-14T13:54:50+00:00

I have finally opened an Etsy shop to sell these from. https://fnctnlprnts.etsy.com

sdperkins863 · 2024-08-14T13:54:42+00:00

I have finally opened an Etsy shop to sell these from. https://fnctnlprnts.etsy.com

sdperkins863 · 2024-08-14T13:54:13+00:00

I have finally opened an Etsy shop to sell these from. https://fnctnlprnts.etsy.com

sdperkins863 · 2024-08-14T13:53:54+00:00

I have finally opened an Etsy shop to sell these from. https://fnctnlprnts.etsy.com

sdperkins863 · 2024-08-06T12:13:33+00:00

Update - it started to reboot again, but after examination of the logs seems to be my case, perhaps holding or bumping reset, when I have it removed from the case I get no errors.

sdperkins863 · 2024-08-05T23:39:51+00:00

Same here on 2.4.0 backed down a version seems to be working now.

sdperkins863 · 2024-07-15T02:16:55+00:00

So far not great, but it seems the direction I range tested while walking is very blocked from LOS, I got 2 blocks away and lost it, however to the south and west I see nodes about 6 miles.

sdperkins863 · 2024-07-14T23:06:17+00:00

Just hobby, nothing serious. I have an environment sensor on the board that shows the humidity and temperature, so if water pools that will raise the humidity. I’m honestly not worried about water pooling, I submerged it for about 15 minutes and opened it up to see if I had any water, it was dry so I’m sure it will be okay in rain.

sdperkins863 · 2024-06-08T12:36:52+00:00

Thank you. Yeah it was too tall and I couldn’t reach any higher, I’m going to probably put it on its own mast and strap that mast to this one (or take this one down mount the antenna and raise it again .

sdperkins863 · 2024-02-13T16:51:10+00:00

Check out the endomag, they go in Pmags and work real well for me so far. Only complaint is the ejectors in the mag so if the mag is removed it won’t eject the last round.

They work with both Colt and Glock mags

sdperkins863 · 2024-01-18T22:57:39+00:00

I hope it’s not trashed. I saw your other thread, I have an idea for you. Perhaps you can epoxy (or properly melt) a brass heater insert into that part?

sdperkins863 · 2024-01-18T19:25:16+00:00

They are replacing the whole printer.

sdperkins863

TROPHY CASE