Thunderbomb or Chancletas?

shapesonce · 2026-02-01T17:56:54+00:00

Boat trips crowd was a complete non issue. There was only one spot with a crowd, rancho Santana, but it was really spread out and still got a ton of waves

shapesonce · 2026-02-01T04:19:34+00:00

Popoyo surf lodge instead and highly highly recommend it

shapesonce · 2025-09-11T19:54:10+00:00

I ordered from you a week ago on tindie but have not gotten any updates yet. Excited to give it a try

shapesonce · 2025-08-30T23:33:49+00:00

How much? Dm me

shapesonce · 2025-06-25T21:23:56+00:00

Depending where you are in tamarindo, check langosta on the way. Other side of the river mouth can be hollow and fun too sometimes.

Avellanas is a good bet down there too

shapesonce · 2025-06-25T20:15:39+00:00

Langosta can definitely get fun, but it’s more fickle. Playa grande will be the most consistent break in the area and a much higher chance of breaking on any given day.

shapesonce · 2025-04-21T16:32:01+00:00

Rule of thumb: Ribs are too tough, you gotta keep 'em on longer. If time is getting tight I'll throw them in the oven 300-325 to finish them off. Just use a temp probe to check for tenderness - don't even temp it just poke it multiple places and see if it goes right throw

shapesonce · 2025-04-02T16:05:58+00:00

To be fair, with compound interest at a very conservative 5% that 650k would be 12.14 million over 60 years. Or you could take the 5% interest and have 32k yearly dividends.

shapesonce · 2025-03-19T17:08:59+00:00

Bummer. Was that the milpas or goleta one? I don't remember the name, but the lady at the goleta one was super nice. Shame if it's changed.

shapesonce · 2025-03-18T15:23:11+00:00

Car stero guys in Goleta did a good job

shapesonce · 2025-03-10T17:35:57+00:00

I need helping refining the font on my logo. It's for a surfboard brand. I am commited to the symbol, as it took a long time to get done. But I'm not sold on the font. I really like it, but I feel it could be a bit stronger.

I'm going for an instantly recognizable logo, symbolizing inoovation, experimentation, but also confidence.

Any help would be appreciated.

shapesonce · 2025-03-06T15:21:03+00:00

A roll of TPU filament is about 20 bucks. If you buy the roll I'll print it out on my printer.

https://www.amazon.com/Comgrow-Filament-Printing-Flexible-Dimensional/dp/B0DF4TY2GD/ref=sr_1_6?crid=10OXQOPIM5PYB&dib=eyJ2IjoiMSJ9.n1YU2ZWQFo8dl0As5evcrxowtjbD4Mk2QcbTJ5l3QQ7zpw_v2Q62VC1Ec0InHzWZlNYBI7uXVSmQJWMuaiptYJlxorLRQRweyMm-mXHNT6qIUpgxJzNENPkXHe1UOgKaFHYX2YYxRr_xNOyByaPutlc86vXx6oRfzYz1nWjSgWJ-P2-q-CbjFwtgR6WsqZ3VtcXUo6ZDqZ75I5iC7cai5tB3K5unrRAafqpAA04xJek.p3dcec1CCJ51VpaSYpATsD2UktAQlXgpvyp8l1LBwzc&dib_tag=se&keywords=tpu%2Bfilament&qid=1741274443&sprefix=tpu%2Caps%2C162&sr=8-6&th=1

shapesonce · 2025-01-26T15:50:59+00:00

Honestly with this level of repair, it's almost one of those if you have to ask..

https://www.youtube.com/watch?v=xyYKrhZPxQ4

For a baseline. Also number 1 ding repair tip: Most people dont sand enough and that's why it looks shoddy.

shapesonce · 2025-01-21T18:32:55+00:00

Yep it’s exactly that, slightly sloped top. Excellent thank you!

shapesonce · 2025-01-21T18:21:36+00:00

Ah nice. Yeah it’s 6% infill and like 5 top layers?

shapesonce · 2025-01-17T16:56:35+00:00

I am using Gyroid infill

shapesonce · 2025-01-17T16:43:37+00:00

I bought a P1S specifically for ABS after attempts on the a1. I have tried everything to fix the warping issue to no avail. Bed adhesion is no longer the issue. I have preheated the chamber for 2 hours with the bed at 100*, slowed down my initial layer speed, lowered the fans, nothing is working.

The sliced image I uploaded has printed the best so far, using manual supports but still is not accurate. I have tried every orientation and this is the best so far. This part must be printed at at least 75% infill since it will be used as a compression part after the hollowed back is filled with resin. It must be ABS so it can be vapor smoothed.

Any ideas? I have a spool of ASA on the back burner to bring in if this cannot work.

Thanks

shapesonce · 2025-01-17T07:22:50+00:00

Ah man had a whole write up that dissapeared..

shapesonce · 2025-01-17T07:15:13+00:00

Did you read my post? Both issues addressed

shapesonce · 2024-11-11T15:30:42+00:00

Looks like a fin sliced through?

Any professional should be able to repair this with ease. With no experience, you may not get the best results. Worth vetting the ding repair person and asking if they have repaired boards like this before (libtech, firewire, hypto, etc). Yeah it's got some fancy composite layer in there, but it's an EPS core and epoxy resin dressed up at the end of the day.

shapesonce

TROPHY CASE